Mitsubishi Electric PUZ-M200YKA2 Service Manual Download Page 89

Page: 89 / 114

OPERATING PROCEDURE

PHOTOS/FIGURES

10. Removing the compressor (MC)

(1) Remove the electrical parts box. (See Photo 4)

(2) Remove the cover panel (front). (See Photo 1)

(3) Remove the cover panel (rear). (See Photo 1)

(4) Remove the valve bed. (See photo 14)

(5) Remove the side panel (R). (See Photo 1)

(6) Remove the front panel fixing screws (5 for front/ 5x12

and 2 for front/ 4x10), then slide the front panel upward

to remove it.

(The front panel is fixed with 4 hooks; 3 on the left side

fixing to the side panel (L), and the other on the right side

fixing to the separator.)

(7) Release the lead wire for FM1 and FM2 from the hole on

separator.

(8) Remove the separator fixing screws (4 for front/ 4x10),

then slide the separator upward to remove it. (The sepa-

rator is fixed to a hook of the side plate.)

(9) Recover refrigerant.

(10) Remove the welded part of compressor (2 positions).

(11) Remove the 3 compressor fixing nuts (M6) to remove the

compressor.

Note 1: Recover refrigerant without spreading it in the air.

Note 2: The compressor can be easily removed by remov-

ing separator.

Photo 14

11. Removing the power receiver

(1) Remove the electrical parts box. (See photo 4)

(2) Remove the cover panel (front). (See Photo 1)

(3) Remove the cover panel (rear). (See Photo 1)

(4) Remove the ball valve fixing screws (2 for front/ 5x16).

(See Photo14)

(5) Remove the stop valve fixing screws (2 for front/ 5x16).

(See Photo14)

(6) Remove the valve bed. (See Photo 14)

(7) Remove the side panel (R). (See Photo 1)

(8) Recover refrigerant.

(9) Remove the welded part of the power receiver (4 posi-

tions) to remove the receiver.

(10) Remove receiver leg fixing screws (2 for front/ 4 x 10),

then slide the power receiver forward to remove it.

(The power receiver is fixed to the base with a hook on

the bottom.)

Note: Recover refrigerant without spreading it in the air.

Photo 15

Compressor

(MC)

Valve bed

Separator

fixing screw

Valve bed

fixing

screws

Compressor

fixing nut

Power

receiver

Ball valve

Stop valve

Valve bed

fixing screw

Stop valve

fixing screws

Receiver leg

fixing screws

Receiver leg

Outlet

Inlet

Compressor

(MC)

Power receiver

Ball valve fixing

screws

OCH775

Summary of Contents for PUZ-M200YKA2



















































































































Search results

Summary of Contents for PUZ-M200YKA2

Reviews:

Related manuals for PUZ-M200YKA2

Brands by name

Popular brands

Mitsubishi Electric PUZ-M200YKA2, Service Manual

Search results

Summary of Contents for PUZ-M200YKA2

Reviews:

Related manuals for PUZ-M200YKA2

Brands by name

Popular brands