Mitsubishi Electric PLA-ZRP100BA Service Manual Download Page 45

Page: 45 / 46

OPERATING PROCEDURE

PHOTOS & ILLUSTRATIONS

10. Removing the drain pump (DP) and float switch (FS)

(1) Remove the drain pan. (See Photo 6)

(2) Cut the hose band and remove the hose.

(3) Remove the drain pump assembly (3 screws and 2 hooks).

(4) Remove the drain pump (3 screws).

(5) Remove the float switch (2 screws).

Photo 7

Photo 8

Drain pump

Hose band

Float switch

Drain pump

assembly fixing screw

Drain pump fixing screw

Float switch fixing screw

11. Removing the heat exchanger

(1) Remove the drain pan. (See Photo 6)

(2) Remove the 3 screws of the piping cover, and pull out

piping cover.

(3) Remove the 2 screws of coil plate.

(4) Remove the 2 screws of the coil.

(5) Remove the screw of the coil support.

(6) Pull out the heat exchanger.

Photo 9

Coil support fixing screw

Heat exchanger

fixing screw

Coil support

Heat exchanger

Coil plate

Piping cover

OCH529

Summary of Contents for PLA-ZRP100BA















































Search results

Summary of Contents for PLA-ZRP100BA

Reviews:

Related manuals for PLA-ZRP100BA

Brands by name

Popular brands

Mitsubishi Electric PLA-ZRP100BA, Service Manual

Search results

Summary of Contents for PLA-ZRP100BA

Reviews:

Related manuals for PLA-ZRP100BA

Brands by name

Popular brands