Mitsubishi Electric MXZ-6F120VGD Installation Manual Download Page 4

3

3. 

Obstacles in front (blowing) only

When there is an obstacle in front of 

the unit as shown in the figure, open 

space above, behind, and on the sides 

of the unit is required.

2. 

Front (blowing) side open

As  long  as  space  indicated 

in  the  figure  is  provided,  it 

is allowed to install the unit 
where obstacles are behind 
and on the sides of the unit. 

(No obstacle above the unit)

FREE SPACE REQUIRED AROUND OUTDOOR UNIT

500 or more

200 or more

350 or more

100 or more

1. 

Obstacles above

When there is no obstacle in front and 
on the sides of the unit, it is allowed 
to install the unit where an obstacle is 

above the unit only if the space shown 

in the figure is provided.

100 or more

500 or more

100 or more

Service space

350 or more 

350 or more

6. 

Service space

Provide space for service and maintenance as shown in the figure.

500 or more

100 or more

100 or more

200 or more

350 or more

500 or more

500 or more

(Unit: mm)

5. 

Obstacles in front, behind and on side(s)

4. 

Obstacles in front and behind

The unit can be used by at-

taching an optional outdoor 

blowing guide (PAC-

SH96SG-E) (but both sides 

and top are open).

100 or more

500 or more

Blowing guide (PAC-SH96SG-E)

Height of the obstacle is 1200 or less

OK

OK

OK

NG

• 

R32 is heavier than air—as well as other refrigerants—so tends to accumulate at the base (in the vicinity of the floor). If R32 accumulates around base, it may reach 

a flammable concentration in case room is small. To avoid ignition, maintaining a safe work environment is required by ensuring appropriate ventilation. If a refriger

-

ant leak is confirmed in a room or an area where there is insufficient ventilation, refrain from using of flames until the work environment can be improved by ensuring 

appropriate ventilation.

•   Refrigerant pipes connection shall be accessible for maintenance purposes.

•   Install outdoor units in a place where at least one of the four sides is open, and in a sufficiently large space without depressions. 

•  When installing the unit in an area that is enclosed with walls such as a 

verandah, be sure to have enough space as shown below. 

  In this case, the air conditioning capacity and power consumption might 

deteriorate.

•  When there is a lack of airflow or there is a possibility of becoming short 

cycle, install an outlet guide and make sure there is enough space behind 

of the unit.

•  When installing two or more units, do not install the units in front or behind 

each other.

VG79Y171H01_4th.indd   3

2020/04/21   10:59:55

Summary of Contents for MXZ-6F120VGD

















Reviews: