En-4
A B C
D E F
A B C
D E F
A B C
E F
A B C
D E F
A B C
D
D E F
DR
DR
DR
DR
DR
P
P
P
P
P
2-1. INSTALLING THE UNIT
Fix here with
M10 bolts.
Make the setting
depth deeper.
Make width wider.
Anchor leg
25 or less
Anchor bolt length
Anchor bolt pitch
(Unit: mm)
2-2. CONNECTING WIRES FOR OUTDOOR UNIT
Terminal block
for power supply
• Be sure to fix the unit’s legs with bolts when installing it.
• Be sure to install the unit firmly to ensure that it does not fall by an earthquake or a gust.
• Refer to the figure in the right for concrete foundation.
• Do not use the drain socket and the drain caps in the cold region.
Drain may freeze and it makes the fan stop.
• Remove the tape on the panel when opening the package. (DO NOT remove the LABELS on the panel.)
1) Remove the service panel.
2) Loosen terminal screw, and connect indoor/outdoor unit connecting wire
(B) from the indoor unit correctly on the terminal block. Be careful not
to make mis-wiring. Fix the wire to the terminal block securely so that
no part of its core is appeared, and no external force is conveyed to the
connecting section of the terminal block.
3) Firmly tighten the terminal screws to prevent them from loosening. After
tightening, pull the wires lightly to confirm that they do not move.
4) Perform 2) and 3) for each indoor unit.
5) Connect power supply cord (A).
6) Fix indoor/outdoor unit connecting wire (B) and power supply cord (A)
with the cable clamps.
7) Close the service panel securely. Make sure that 3-2. PIPE CONNEC-
TION is completed.
• After making connections between both power supply cord (A) and
indoor/outdoor unit connecting wire (B), be sure to fix both cable and
wire with cable clamps.
Connecting order
• Connect the terminal block in
following order.
A
→
B
→
C
→
D
→
E
→
F
→
P
→
DR
Terminal block for indoor/outdoor unit
Cable clamps
600
370
Service panel
Screws
Note:
• Removing the handle increases the effectiveness of the wiring operation.
• Be sure to reinstall the handle.
2. OUTDOOR UNIT INSTALLATION
Terminal block
for DRED Interface
DRED Interface
Power supply
35 mm
15 mm
Lead wire
• Be sure to attach each screw to its correspondent
terminal when securing the cord and/or the wire to
the terminal block.
• Make earth wire a little longer than others.
(More than 35 mm)
• For future servicing, give extra length to the con-
necting wires.
1 2 3 C
<OUTDOOR UNIT>
Indoor/outdoor unit
connecting wire
<INDOOR UNIT>
Terminal block
Terminal block
Terminal block
Terminal block for
power supply
Terminal block
<INDOOR UNIT>
POWER SUPPLY
~/N 230 V 50 Hz
This unit has demand response capability which is compliant with AS/NZS 4755.3.1. To activate this function, you need to make a contract with remote
agents such as electric supply company, then this unit should be connected to Demand response enabling devise (DRED). For further information,
consult your dealer. This unit supports 3 Demand Response Modes (DRMs): DRM1, DRM2 and DRM3.
CAUTION
• To prevent malfunction caused by noise, route the cord connecting this unit to DRED and the power supply cord as parallel as possible.
• Do not connect the demand control transmission cable to the terminal block for power supply.
• Do not pull, extremely bend or apply strong pressure on the wire to prevent failure.
• Do not screw DRED to outdoor unit.
• Do not put DRED in outdoor unit.
• Secure electrical wiring above clamp.
• Do not get DRED wire caught in the service panel.
1 : DRM 1
2 : DRM 2
3 : DRM 3
C : COMMON
AS/NZS4755
terminal block
