Cut off the
extra length.
3LSH¿[LQJ
band (E)
Fixing screw (F)
1-4. INSTALLATION DIAGRAM
When the piping is to be attached to a wall containing metals (tin plated)
RUPHWDOQHWWLQJXVHDFKHPLFDOO\WUHDWHGZRRGHQSLHFHPPRUWKLFNHU
between the wall and the piping or wrap 7 to 8 turns of insulation vinyl tape
around the piping.
To use existing piping, perform COOL operation for 30 minutes and pump
GRZQEHIRUHUHPRYLQJWKHROGDLUFRQGLWLRQHU5HPDNHÀDUHDFFRUGLQJWR
the dimension for new refrigerant.
Note:
*1 Place indoor/outdoor unit connecting wire (A)
and power supply cord (K) at least 1 m away
from the TV antenna wire.
Drain piping for outdoor unit
• Provide drain piping before indoor and
outdoor piping connection.
• Connect drain hose (I) I.D.15 mm as shown
in the illustration.
0DNHVXUHWRSURYLGHGUDLQSLSLQJZLWKD
GRZQKLOOJUDGHIRUHDV\GUDLQÀRZ
Note:
Install the unit horizontally.
'RQRWXVHGUDLQVRFNHWLQFROGUHJLRQV'UDLQPD\IUHH]HDQG
PDNHWKHIDQVWRS
The outdoor unit produces condensate during the heating operation.
Select the installation place to ensure to prevent the outdoor unit and/
or the grounds from being wet by drain water or damaged by frozen
drain water.
IMPORTANT NOTES
• Units should be installed by licensed contractor according to local code
UHTXLUHPHQWV
•
7RFRPSO\ZLWKWKHUHTXLUHPHQWVRI$XVWUDOLDQVWDQGDUG$61=6
HOHFWULFDOLQVWDOODWLRQVZLULQJUXOHVWKHHOHFWULFDOZLULQJUHTXLUHGEHWZHHQ
the indoor and outdoor units must be installed by a licenced electrical
contractor
.
•
&KHFNWKDWFDEOLQJZLOOQRWEHVXEMHFWWRZHDUFRUURVLRQH[FHVVLYHSUHV
-
sure, vibration, sharp edges or any other adverse environmental effects.
7KHFKHFNVKDOODOVRWDNHLQWRDFFRXQWWKHHIIHFWVRIDJLQJRUFRQWLQXDO
vibration from sources such as compressors or fans.
$IWHUWKHOHDNWHVWDSSO\LQVXODWLQJPDWHULDOWLJKWO\VR
that there is no gap.
WARNING
7RDYRLGULVNRI¿UHÀDUHFRQQHFWLRQVKRXOGEHLQVWDOOHGRXWGRRUV
5HXVDEOHPHFKDQLFDOFRQQHFWRUVDQGÀDUHGMRLQWVDUHQRWDOORZHG
indoors.
WARNING
7RDYRLGULVNRI¿UHHPEHGRUSURWHFWWKHUHIULJHUDQWSLSLQJ
([WHUQDOGDPDJHRQWKHUHIULJHUDQWSLSLQJFDQEHFDXVHRI¿UH
Be sure to use wall hole
sleeve (C) to prevent in-
door/outdoor connecting
wire (A) from contacting
metal parts in the wall
and to prevent damage by
rodents in case the wall
is hollow.
Indoor unit
Wall hole
sleeve (C)
Wall hole cover (D)
Seal the wall hole gap
with putty (H).
Fix the pipe to wall
ZLWKSLSH¿[LQJEDQG
(E).
(9)
(I)
PARTS TO BE PROVIDED AT YOUR SITE
(A) Indoor/outdoor unit connecting wire*1
1
(B) Extension pipe
1
(C) Wall hole sleeve
1
(D) Wall hole cover
1
(E)
3LSH¿[LQJEDQG
2 to 5
(F) Fixing screw for (E) 4 × 20 mm
2 to 5
(G) Piping tape
1
(H) Putty
1
(I)
Drain hose
(or soft PVC hose, 15 mm inner
diameter or hard PVC pipe VP16)
1 or 2
(J) Refrigeration oil
1
(K) Power supply cord*1
1
ACCESSORIES
&KHFNWKHIROORZLQJSDUWVEHIRUHLQVWDOODWLRQ
<Indoor unit>
(1) Installation plate
1
(2)
,QVWDOODWLRQSODWH¿[LQJVFUHZ
4 × 25 mm
7
(3) Wireless remote controller
1
(4)
Felt tape
(For left or left-rear piping)
2
(5) Remote controller holder
1
(6)
Fixing screw for (5) 3.5 × 16 mm
%ODFN
2
(7) Battery (AAA) for (3)
2
(8)
$LUFOHDQLQJ¿OWHU
2
<Outdoor unit>
(9)
'UDLQVRFNHW
1
Air inlet
Air inlet
Air outlet
Outdoor unit installation
40 mm
2-10 mm × 21 mm slot
840 mm
500 mm
390 mm
330 mm
349-371 mm
175 mm
(G)
(E)
(C)
(4)
(D)
(F)
(7)
(3)
(5)
(6)
(8)
72 mm or
more/130 mm
or more for left /
left rear piping (us-
ing spacer)
Note:
Do not
obstruct the
air outlet.
220 mm
or more
120 mm
or more
10 mm or more
PRUPRUHIURPWKHÀRRU
Up to 2.3 m is recommended.
Appearance of the outdoor unit may differ from some models.
clear *2
100 mm
or more
100 mm
or more
350 mm
or more
500 mm *3
or more
*2 500 mm or more when front
and sides of unit are clear
*3 When any 2 sides of left, right and rear
of unit are clear
