8
COOL & HEAT type
1
Press the EMERGENCY OPERA-
TION switch.
* Each time the EMERGENCY OPERATION
switch is pressed, the unit will operate in order
of EMERGENCY COOL MODE, EMER-
GENCY HEAT MODE and STOP MODE.
However, when the EMERGENCY OPERA-
TION switch is once pressed, the unit will op-
erate in test run for 30 minutes and then the
operation mode shifts to EMERGENCY MODE.
Details of EMERGENCY MODE are as shown below.
However, the temperature control does not work for 30
minutes in test run and the unit is set to continuous
operation. The fan speed is set to Hi in test run and
shifts to Medium after 30 minutes.
Operation mode
COOL
HEAT
Set temperature
24
°
C
24
°
C
Fan speed
Medium
Medium
Horizontal vane
Auto
Auto
The operation mode is indicated by the Operation Indi-
cator lamp on the indoor unit as following figures.
Operation Indicator lamp
EMERGENCY COOL EMERGENCY HEAT
STOP
■
To stop the emergency operation,
press the EMERGENCY OPERA-
TION switch once (in case of EMER-
GENCY HEAT MODE) or twice (in
case of EMERGENCY COOL MODE).
Operation
Indicator
Operation
Indicator
Operation
Indicator
PREPARATION BEFORE OPERATION
When the remote controller cannot be used (emergency operation)
When the batteries of the remote controller run out or the remote controller malfunctions, the emergency operation
can be done using the EMERGENCY OPERATION switch.
COOL ONLY type
1
Press the EMERGENCY OPERA-
TION switch.
* When the EMERGENCY OPERATION switch
is pressed, the unit will operate in test run for
30 minutes at first and then the operation mode
shifts to EMERGENCY COOL MODE.
Details of EMERGENCY COOL MODE are as shown be-
low. However, the temperature control does not work
for 30 minutes in test run and the unit is set to continu-
ous operation. The fan speed is set to Hi in test run and
shifts to Medium after 30 minutes.
Operation mode
COOL
Set temperature
24
°
C
Fan speed
Medium
Horizontal vane
Auto
The operation mode is indicated by the Operation Indi-
cator lamp on the indoor unit as following figures.
Operation Indicator lamp
EMERGENCY COOL
STOP
■
To stop the EMERGENCY COOL
MODE, press the EMERGENCY OP-
ERATION switch again.
* Each time the switch is pressed, the operation
mode alternates between the EMERGENCY
COOL MODE and STOP MODE.
Operation
Indicator
Operation
Indicator
Handling of the remote controller
•
The range that the signal can reach is about 6 m when the remote controller is pointed at the front of the
indoor unit.
•
When a button is pressed, one or two beeps will be heard from the indoor unit. If no sound is heard, operate
again.
•
Use the remote controller carefully.
If it is dropped, thrown or it gets wet, the remote controller may not operate.
When installing on a wall, etc.
•
Install the remote controller installation case in a position where the signal reception sound (beep) can be
heard from the indoor unit when the
ON/OFF
button is pressed.
How to install/remove the remote controller
Installing
Insert the remote controller downward.
Removing
Pull it up.
Dry-cell batteries
Reference for replacing batteries
When the indoor unit does not respond to the signal from the remote controller, or the display becomes dim,
replace the batteries with new ones (size AAA).
•
Though both alkaline batteries and manganese batteries can be used, alkaline batteries are recommended
because their service life is longer than that of manganese batteries.
•
The service life of an alkaline battery is about 1 year.
However, a battery which the time limit is approaching may be exhausted soon. The recommended usable
time limit is indicated (month/year) on the bottom of the battery.
•
Replace the 2 batteries with new ones of the same type.
•
Do not use rechargeable batteries.
•
To prevent liquid leakage, take out all batteries when the remote controller is not going to be used for a long
time.
•
Dispose of exhausted batteries in the correct manner.
Remote controller
installation case
