Mitsubishi Electric MS-09SN-C1 Service Manual Download Page 46

Page: 46 / 60

11-3. MU-09SN -

MU-10SN -

MU-12SN -

MU-09SN -

MU-10SN -

MU-12SN -

OUTDOOR UNIT

OPERATING PROCEDURE

PHOTOS

1. Removing the cabinet

(1) Remove the screws of the top panel.
(2) Remove the screw of the service panel.
(3) Remove the screws of the cabinet.
(4) Remove the screws of the front panel and motor support.
(5) Remove the service panel, and remove the screw from

the insides.

(6) Remove the top panel.
(7) Remove the cabinet.

Photo 1

Photo 3

Screws of the
top panel

Service
panel

Screws of the
service panel

Screws of
the top panel

Screws of
the cabinet

Screws of the cabinet

Photo 2

Screws of the front panel
and motor support

2. Removing the electrical parts

(1) Remove the service panel and the cabinet.(Refer to 1)
(2) Remove the following parts.

•Compressor capacitor (C1)
•Outdoor fan capacitor (C2)
•Terminal block

Photo 4

Screws
of the
cabinet

Outdoor fan capacitor

Compressor capacitor

Terminal block

OB256-2qxp 2.2.8 9:11 AM Page 46

Summary of Contents for MS-09SN-C1





























































Search results

Summary of Contents for MS-09SN-C1

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MS-09SN-C1, Service Manual

Search results

Summary of Contents for MS-09SN-C1

Reviews:

Brands by name

Popular brands