manualshive.com logo in svg

Mitsubishi Electric MS-09SN-C1, Service Manual

Share
Download
Mitsubishi Electric MS-09SN-C1 Service Manual Download Page 42

42

DISASSEMBLY INSTRUCTIONS

11

OPERATING PROCEDURE

PHOTOS

Photo 1

Photo 2

Screws

Front panel

11-1. MS-09SN -

MS-10SN -

MS-09SN -

MS-10SN -

INDOOR UNIT

C2

C2

C1

C1

(1)  Slide the sleeve and check if there is a locking lever or not.

(2) The terminal with this connector is a terminal 
     with lock mechanism.

1

Slide the sleeve.

2

Pull the terminal while 

   pushing the locking
   lever.

1

Hold the sleeve, and 

   pull out the terminal 
   slowly.

In case of terminal with lock mechanism, detach the terminal as shown below.
There are two types ( Refer to (1) and (2)) of the terminal with lock mechanism.
The terminal with no lock mechanism can be removed by pulling it out.
Check the shape of the terminal and work.

<"Terminal with lock mechanism" Detaching points>

Connector

Sleeve

Locking lever

1. Removing the front panel

(1) Remove the screw caps of the front panel.

Remove the screws.

(2) Pull the panel down to your side slightly and unhook the

catches at the top.

V.A. clamp

Screw of the
V.A. clamp

Room temperature
thermistor connector

Cord clamp

Indoor electronic
control P.C. board

Screw of the ground wire

Vane motor 
connector 

Fan motor connector 

2. Removing the electronic control P.C. board and the

power monitor, receiver P.C. board

(1) Remove the front panel. (Refer to 1)
(2) Remove the screw of the electrical cover.

Remove the electrical cover.

(3) Remove the V.A. clamp.
(4) Remove the cord clamp.
(5) Remove the screw of the terminal block.
(6) Remove the screw of the ground wire.
(7) Disconnect all the connectors and all the lead wires on the

electronic control P.C. board.

(8) Remove the R.L holder.
(9) Remove the electronic control P.C. board.
(10) Open the R.L holder and the power monitor, receiver P.C.

board.

R.L holder

Power monitor,
receiver P.C.
board

OB256-2qxp  2.2.8 9:10 AM  Page 42

Summary of Contents for MS-09SN-C1





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands