manualshive.com logo in svg

Mitsubishi Electric MS-09SN-C1, Service Manual

Share
Download
Mitsubishi Electric MS-09SN-C1 Service Manual Download Page 45

45

OPERATING PROCEDURE

PHOTOS

Photo 3

Photo 4

Screw of the
heat exchanger 

Catch

Bearing support
screws

Heat exchanger

Photo 5

3. Removing the electrical box

(1) Remove the front panel. (Refer to 1)
(2) Remove the electrical cover.
(3) Disconnect the connector of the indoor coil thermistor.
(4) Disconnect the motor connector (CN211 and CN121) and

the vane motor connector (CN151) on the electronic con-
trol P.C. board.

(5) Remove the screw of the electrical box, remove the electri-

cal box.

Screws
of the
vane
motor

Vane motor

4. Removing the vane motor

(1) Remove the front panel. (Refer to 1)
(2) Remove the electrical box. (Refer to 3)
(3) Pull out the drain hose from the nozzle assembly, remove 

the nozzle assembly.

(4) Remove the screws (both upper and lower) of the vane 

motor, disconnect the connector.

(5) Remove the vane motor.

5. Removing the indoor fan motor and the line flow fan

(1) Remove the front panel.
(2) Remove the electrical box.
(3) Unhook the catches on the both sides of the nozzle 

assembly.

(4) Remove the nozzle assembly.
(5) Remove the screws of the bearing support.
(6) Remove the screw of the heat exchanger unhook the catch.
(7) Lifting the heat exchanger, remove the bearing support.
(8) Loose the screw fixing the line flow fan, remove the line 

flow fan.

(9) Remove the screws of the motor band, remove the fan

motor.

Screw of the
ground wire

Screw of the
electrical cover

Screw of the 
electrical cover

Indoor fan motor

Line flow fan

Screw of the
motor band

Screws
of the
motor
band

OB256-2qxp  2.2.8 9:11 AM  Page 45

Summary of Contents for MS-09SN-C1





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands