manualshive.com logo in svg

Mitsubishi Electric MR-J5 Series, User Manual

The Mitsubishi Electric MR-J5 Series is a cutting-edge product designed for precision and efficiency. Enhance your understanding and operation of this advanced technology with our comprehensive User Manual, available for free download at manualshive.com. This manual offers detailed instructions and insightful tips to maximize the potential of your MR-J5 Series.

Share
Download
background image

10  USING A DIRECT DRIVE MOTOR

10.8  Battery

307

10

Assembly of the case
After all MR-BAT6V1 batteries are mounted, fit the cover and insert screws into the two holes and tighten them. Tightening 
torque is 0.71 N•m.

When assembling the case, be careful not to get the lead wire caught in the fitting parts or the screwing parts.

Precautions for removal of battery
The connector attached to the MR-BAT6V1 battery has the lock release lever. When removing the connector, pull out the 
connector while pressing the lock release lever.
 • Battery cable removal

Precautions

 • Pulling out the connector of the MR-BT6V1CBL and MR-BT6V2CBL without the lock release lever pressed may damage 

the CN4 connector of the servo amplifier or the connector of the MR-BT6V1CBL or MR-BT6V2CBL.

Screw

While pressing the lock release lever, 
pull out the connector.

Battery cable

Summary of Contents for MR-J5 Series





























































































































































































































































































































Reviews:

No comments

Related manuals for MR-J5 Series

Baldwin Boxall BV225 Installation Instructions Manual preview
BV225
Brand: Baldwin Boxall Pages: 16
Larcan MX Series Technical Manual preview
MX Series
Brand: Larcan Pages: 13
JEFF ROWLAND 525 Operational Manual preview
525
Brand: JEFF ROWLAND Pages: 18
EAW CAM150 Specifications preview
CAM150
Brand: EAW Pages: 2
Fender Custom Vibrolux Reverb Service Diagram preview
Custom Vibrolux Reverb
Brand: Fender Pages: 2
Warfedale Pro WX-1 Operating Manual And User Manual preview
WX-1
Brand: Warfedale Pro Pages: 12
Yamaha HR-1000 Owner'S Manual preview
HR-1000
Brand: Yamaha Pages: 4
B&K ST55.2 Owner'S Manual preview
ST55.2
Brand: B&K Pages: 16
Ultimate T2-5001 Instruction Manual preview
T2-5001
Brand: Ultimate Pages: 24
Audio Reveal first Instruction Manual preview
first
Brand: Audio Reveal Pages: 14
FMS EMGZ470A.W Operating Manual preview
EMGZ470A.W
Brand: FMS Pages: 24
Xicom AND XT-100 Operation & Installation Manual preview
AND XT-100
Brand: Xicom Pages: 36
Harman harman/kardon CITATION AMP Manual preview
harman/kardon CITATION AMP
Brand: Harman Pages: 42
Concert Fidelity CF-080LS Owner'S Manual preview
CF-080LS
Brand: Concert Fidelity Pages: 8
Mechanics & Electronics ME750-FD Operating Manual preview
ME750-FD
Brand: Mechanics & Electronics Pages: 11
Symetrix SX204 Owner'S Manual preview
SX204
Brand: Symetrix Pages: 11
MTS Systems MPA-03 SL Manual preview
MPA-03 SL
Brand: MTS Systems Pages: 22
Phoenix Gold The One Limited Edition Amplifier Manual preview
The One Limited Edition Amplifier
Brand: Phoenix Gold Pages: 8

Brands by name

Popular brands

Load more brands