Mitsubishi Electric MLZ-KP09NA, Installation Manual

Page: 5 / 36

En-4
2-1. CEILING oPENINGs AND susPENsIoN
BoLt INstALLAtIoN LoCAtIoNs
• Install the indoor unit at least 7 ft. (2.2 m) above floor or grade level.
For appliance not accessible to the general public.
• Refrigerant pipes connection shall be accessible for maintenance
purposes.
• Make an opening in the ceiling 15-1/8 × 45-11/16 in. (384 mm × 1160
mm) in size. This functions as a check window and will be needed later
during servicing.
• If the dimensions are not accurate, when the grille is installed there
may be gaps between it and the indoor unit. This may result in dripping
water or other problems.
• When deciding on placement, consider carefully the space around the
ceiling and make your measurements generous.
• Ceiling types and building construction differ. Therefore you should
consult with the builder and decorator.
• Using the installation template (top of the package) and the gauge
(supplied as an accessory with the grille), make an opening in the
ceiling so that the main unit can be installed as shown in the diagram.
(The method for using the template and the gauge are shown.)
• Use W3/8 suspension bolts
E
.
• After suspending the indoor unit, you will have to connect the pipes
and wiring above the ceiling. Once the location has been fixed and the
direction of the pipes has been determined, place the refrigerant and
drainage pipes, and the wiring that connects the indoor and outdoor
units in their desired locations before suspending the indoor unit. This is
especially important in cases where the ceiling is already in existence.
• The packing material (cushion) is taped to the unit. When using the
packing material, do not remove it from the unit to prevent horizontal
vane damage.
1) Wooden structures
• Use tie beams (single storied houses) or second floor beams (two
story houses) as reinforcing members.
• Wooden beams for suspending air conditioners must be sturdy and
their sides must be at least 2-3/8 in. (60 mm) long if the beams are
separated by not more than 35-7/16 in. (900 mm) and their sides
must be at least 3-9/16 in. (90 mm) long if the beams are separated
by as much as 6 ft. (1800 mm).
• Use channel, duct and other parts procured locally to suspend the
indoor unit.
2) Ferro-concrete structures
• Secure the suspension bolts using the method shown, or use steel
or wooden hangers, etc. to install the suspension bolts
E
.
• When the unit is put down with its lower surface facing down, place
packing material (cushion) underneath to prevent horizontal vane
damage.
Do not remove.
Horizontal vane may be damaged.
Packing material (cushion)
Align center of ceiling opening and bolt distance
Outlet
(underside)
Air
outlet
2-1/8 2-1/8
13/16 13/16
41-3/8
45-11/16 Ceiling opening
47-1/4 Grille outlet
unit: inch
16-11/16 Grille outlet
13/16
13/16
1-1/2
1-1/2
15-1/8 Ceiling
opening
12-1/8
12-1/8 in.
(308 mm)
2. INDooR uNIt INstALLAtIoN
Ceiling panel
Rafter
Beam
Roof beam
Use inserts rated at
220 to 330 lb (100-
150 kg) each
Suspension bolts W3/8
C channel
41-3/8 in.
(1051 mm)
Channel suspension
bracket
Suspension bolt
Steel reinforcing rod
• Remove the packing material (cushion) before installing the plastic
bag and the cover.
• To prevent from dust, protect the indoor unit by covering with the
plastic bag and the cover.
• Remove the plastic bag and the cover before installing the grille
(optional).
• When the distance between joints is 15-1/8 in. (348 mm) or less,
please refer to the notice affixed to the packing material.
Plastic bag
Cover
Align center of ceiling opening and bolt distance
Outlet
(underside)
Air
outlet
54.5
20
1051
1160 Ceiling opening
1200 Grille outlet 54.5
20
unit: mm
20
424 Grille outlet
20
38
38
384 Ceiling opening
308
RG79Y948H01_en.indd 4 2018/01/23 11:41:54