background image

17

Operating

E

Using Timer

When using the timer, drain the water from the tank before beginning operation. When the tank becomes full of water, 
dehumidifying cannot be performed because operation stops.

OFF Timer Operation

You can set an operating time between 1 to 9 hours. 
Set the time when you turn the power ON.

1

2

1

Turn the power ON 

P12

Set the desired operating mode and swing 
direction.  P12~16

2

Press 

 to select the 

operating time

If you press the switch once, “ ” and 

” are displayed.

Each press changes the indication in the 
order of “1 to 9” and “no indication (cancel)” 
(the indication changes automatically if you 
continue pressing the switch).

Off Timer Operation Starts

<Display example>

Humidity setting 
(set to 60%)
Swing “WIDE”
Off timer is set 
to 2 hours

The remaining operation time indication 
is reduced by 1 as each hour elapses.
When the set time elapses, operation 
stops and the louvre closes automatically.
The POWER lamp goes out and the 
operating mode indication disappears.

When the drying inside operation (AUTO) is set, 
the drying inside operation is performed.  P19

<When you want to cancel the timer 
before the set time elapses>

When you want to end operation

Press the POWER switch (POWER OFF).

When you want to cancel the off timer 
and continue operation 

Press the ON/OFF TIMER switch repeatedly 
until the remaining time indication 
disappears (returns to continuous operation).

Information

The off timer and on timer cannot be set at the same time.
If you use INTELLIGENT LAUNDRY or BATHROOM 
MILDEW GUARD in conjunction with the off timer, the 
operation may stop before drying is complete.
The off timer cannot be set while the drying inside 
operation is being performed.

ON Timer Operation

You can set an operating start time between 1 to 9 
hours. Set the time when you turn the power OFF.

1

2

3

1

Turn the power OFF 

P12

2

Press 

 to select the 

operating start time

If you press the switch once, the POWER 
lamp, operating mode indication, and “ ” 
fl ash, and “

” is displayed.

Each press changes the indication 
in the order of “1 to 9 hours” (the 
indication changes automatically if 
you continue pressing the switch).

3

Press 

 to confi rm the 

operating start time

The POWER lamp and time indication fl ash

On Timer Reservation Completes

The time indication and operating mode 
indication fl ash and an alarm sounds to 
notify if you forget to press the switch.

(The alarm (pipi...) sounds for one minute.)

<Display example>

Humidity setting 
(set to 60%)
Swing “WIDE”
On timer is set 
to 5 hours

The remaining time until operation 
indication is reduced by 1 as each 
hour elapses.
When the set time elapses, operation 
starts.

<When you want to cancel the timer 
before the set time elapses>

Press the POWER switch (POWER OFF).

Information

If you set the on timer during the drying inside operation, 
the drying inside operation is cancelled.
The on timer operation cannot be performed with a 
commercially available power socket that has a timer.

e̲mj̲e26cx̲h.indb   17

e̲mj̲e26cx̲h.indb   17

2009/10/26   17:22:23

2009/10/26   17:22:23

Summary of Contents for MJ-E26CX-H



























Reviews: