manualshive.com logo in svg

Mitsubishi Electric MA-EF303HS-U, Instruction Manual, Page: 15 / 16

Share
Download
Mitsubishi Electric MA-EF303HS-U Instruction Manual Download Page 15

Press the power switch and turn on the 
power.

Reinsert the power plug into the power 
outlet.

Clean the sensors.

Replace the HEPA filter and the 
activated charcoal filter.

Clean the sensors.

Replace the HEPA filter and the 
activated charcoal filter.

Clean the Plasma unit.

Reset the intake grill, the HEPA filter 
and the activated charcoal filter.

Replace with new batteries, or correctly set 
the batteries observing the proper polarity.

12~13

14

14

8

13

8

Symptom

Cause

Remedy

Symptom

Cause

The odor monitor does not change 
even when an odor can be noticed

The sensitivity of the sensor differs depending on odor ingredients, and the 
monitor display may at times remain unchanged.

● 

The following symptoms are not malfunctions.

Should the problem persist after having checked the above list, stop using the unit, remove the power plug and contact 
your dealer of purchase or Mitsubishi Electric.
 

There is no air intake

Odor and smoke are 
not completely 
removed

Is the fan level lamp on?
(Is the power on?)

Is the power plug securely inserted into 
the power outlet?

Are the sensors dusty?

During the Plasma deodorization, you may hear a small hissing noise or notice an ozone smell.
(The level of noise and degree of the smell of ozone will vary depending on the environment. 
The generated ozone is of low concentration and is harmless to the body.)

The monitors do not change much
(Odor monitor, microdust monitor and 
pollen monitor)

Is the room too large?

Use the unit within the range of the applicable floor area.

Checking monitor operation:

● 

Rub tissue paper in front 

of the main unit to 
discharge dust.

● 

Blow cigarette smoke.

If there is a large volume of dust or odor, it may 
take some time for the air to become clean.

The monitor lamp flashes

The monitor lamp will flash until the sensors become stable, even if the 
power is turned on immediately after inserting the power plug.

The monitor lamp flashes even when 
the room is clean

The sensor may at times respond to a breeze from air conditioners within 
the room, and gases that are unnoticeable to the human smell.

Is the unit operating in AUTO (NORMAL) mode?
The unit will stop operation when the air is clean.

Are the sensors dusty?

Fan noise and 
vibration are louder 
than before

Plasma deodorization 
lamp flashes

There is an abnormal electrical 
discharge.

Is the activated charcoal filter still 
wrapped in plastic?

One of the following lamps flash:
FAN/POLLEN GUARD/NORMAL

Are the intake grill, the HEPA filter and 
the activated charcoal filter properly set?

The remote controller 
does not work

Main unit vibrates 
heavily

Little monitor response

Is the unit installed on an unstable or 
unlevel surface?

Install on a level and stable surface.

Is the HEPA filter or the activated 
charcoal filter dirty?

12~13

Is the HEPA filter or the activated 
charcoal filter dirty?

Remove the plastic and replace.

Have the batteries been completely depleted or are 
 the        and       of the batteries set correctly?

The air fan does not turn, or there 
is no air discharge

A small hissing noise is heard, or there 
is a smell of ozone during the Plasma 
deodorization

Tr

oub
le-

shooting

15

Maintenance

Troubleshooting

Replacing the filters

T

roub

leshooting

Summary of Contents for MA-EF303HS-U

















Reviews:

No comments