background image

 

  

5

For assistance call 1(877) 675-2224

 Laser  Safety

Laser Safety

• 

This TV is in compliance with the requirements of IEC 
60825-1 Ed. 2(2007).

• 

This TV is a CLASS 1 laser product.  This TV poses 
no risk to eyes or skin during normal use.  An expo-
sure hazard may exist only if the protective housing 
is removed.

• 

This TV contains a CLASS 4 laser device, which by 
itself may be hazardous.  However, this TV incorpo-
rates a protective housing, optics and electronics 
such that there should be no exposure to unsafe 
levels of laser light during normal operation and 
proper service.

• 

Do not open this product.  No consumer controls 
are inside.  Only a trained LASERVUE® technician 
should service this TV.  Please call Mitsubishi for 
assistance at 1 (877) 675-2224.

Safe Operation

• 

Always inspect the TV for damage after moving 
it.  If the cabinet or screen is physically damaged, 
DO NOT connect the TV to an AC outlet.  Call 
1 (877) 675-2224 for assistance.

DO NOT power on the TV until it has been repaired 
by qualified service personnel authorized by 
Mitsubishi.  See  “Service and Customer Support” 
page 34 .

• 

Caution.

  Use of controls or adjustments or per-

formance of procedures other than those specified 
herein may result in hazardous radiation exposure.

• 

Use external or remote controls to operate the 
product.  Connection to signal sources and power 
are accomplished through the external connectors.

Damage and Repair

• 

There are no user serviceable components in this 
TV.  Do not attempt to disassemble any part of the 
TV.

• 

If damaged, the device must not be powered on or 
used until it is repaired by qualified service person-
nel authorized by Mitsubishi.  See  “Service and 
Customer Support” page 34 .

• 

Under no circumstances shall attempts be made to 
operate this device without the screen in place or if 
any portion of the enclosure, including the screen, 
is cracked, broken, a liquid is spilled onto the TV or 
is otherwise damaged.

CAUTION

CLASS 4 LASER LIGHT WHEN 

OPEN AVOID EYE OR SKIN 

EXPOSURE TO DIRECT OR 

SCATTERED RADIAITON

ATTENTION

LUMIÈRE LASER DE CLASSE 4 - EN CAS 

D’OUVERTURE EXPOSITION DANGERE-

USE AU RAYONNEMENT DIRECT OU 

DIFFUS DES YEUX OU DE LA PEAU

This class-4 label and similar service warning labels 
are located inside the back cover of the television in an 
area that should not be accessed by the user under any 
circumstances.

An additional class-4 label is located at the lower front 
access panel under the front decorative bezel.

This class-4 label is located at the center back of the TV 
under the outer cover.

This label is located on the right lower back of the 
television set.

Summary of Contents for LASERVUE L75-A94



















































Reviews: