Mitsubishi Electric k-con KSGD-01WS-B Installation And Operation Manual Download | Manualshive

Page: 10 / 16

background image

Installation and operation manual

KSGD02 Revision: 1.4

Page 10 of 16

R

KSGD-01WS-B

2.3 Other features

Features such as the sensor and buzzer enable link are located on the front of the detector PCB.

When the buzzer enable / disable link is fitted, the buzzer will operate when required. Remove
this link to disable the buzzer permanently.

i

Status LED

Buzzer

Buzzer Enable / Disable link

Sensor

Factory use only

Fig 2.4 KSGD other features

«
...
8
9
10
11
12
...
»

Summary of Contents for k-con KSGD-01WS-B

















Reviews:

No comments

Related manuals for k-con KSGD-01WS-B

BL-C1A - Network Camera

Brand: Panasonic Pages: 19

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 36

Brand: Barnett Engineering Pages: 3

Toolsplit TSCE-500

Brand: Tecnosystemi Pages: 8

Brand: Olympia Pages: 92

Brand: Iget Pages: 2

Brand: OEM Optical Pages: 25

Brand: ALIBI Pages: 6

Brand: IDS Pages: 8

XRX300 LED Series

Brand: WE-EF Pages: 6

Brand: MeiTrack Pages: 8

Brand: Sercomm Pages: 73

Brand: DiSS Pages: 30

EyeZen RF ZPDEZRF868

Brand: Zennio Pages: 15

MEGApix DWC-MB45iALPRT

Brand: Digital Watchdog Pages: 84

Brand: Suresafe Pages: 3

Brand: 3scort Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands