background image

English

NA 

-

 9

Maintenance - Continuation

Cleaning the air fi lter

3

Around once a week

Caution

A dirty air fi lter will shorten the working life of the motor and heater and decrease the drying performance 

due to insuffi cient air volume and air speed and bacteria can grow in the fi lter area due to dust deposits.

Air fi lter

Air fi lter

1

 Pull the tab, open the front cover and turn the 

sensor switch "OFF".

  The sensor light "OFF" is lit.

Reattach the air fi lter.

  Make sure that the air filter is fitted properly. 

(Dirt and dust may get into the unit and shorten its 
working life if the air fi lter is out of position.)

5

 Turn the sensor switch "ON" and close the 

front cover so that there is no gap and push 
the tab.

  The sensor light "ON" is lit.

2

 Remove the air fi lter.

3

 Clean the air fi lter.

  Tap it lightly or vacuum off the dust.
  Wipe with lukewarm or cold water if it is extremely 

unclean.

NOTE

  After washing the air filter with water, dry it thoroughly.

Caution

  Never dry the air filter with a heat source such as a hair 

dryer.

Water may enter the unit and cause short 
circuits, electric shocks or damage if the front 
cover is left open.

Caution

Front cover

Open

Sensor

light

Sensor

switch

Summary of Contents for Jet Towel JT-MC106G-W-NA













Reviews: