background image

42

CYCLIC TRANSMISSION

6.1

Common memory

Concept of common memory is stated below.
(1) The common memory is used as a shared memory between nodes which perform cyclic transmission.
(2) The common memory has two areas which are "common memory area 1" and "common memory area 

2".
Common memory area 1 is I/O data area. Common memory area 2 is the control information area.
Two different areas can be assigned to each node.

(3) When the area each node sends exceed the transmission size (1024 byte) by one frame, data is 

transmitted by multiple frames.

(4) When receiving data which are divided into multiple frames as (3), common memory is not updated until 

all frames sent from one node are received. Synchronism per node unit is guaranteed.

(5) Entire network has an area of 8k bit (0.5k word) + 8k word = 8.5k word.

The maximum send data capacity per one node is 8.5k word. (Note that one word is 2 byte.)

2

15

2

0

0.5k Word

8k Word

=Input/output data area

Common memory area 1

Common memory area

8.5k Word

=Control information area

Common memory area 2

Summary of Contents for FR-F740-01160-EC










































































































Reviews: