Mitsubishi Electric EMU4-D65, Instruction Manual

Page: 11 / 16

- 11 -
Screen Operation Note
5 Save the settings
5-1.
（
1
）
After setting all of the items, push the Setup key.
（
2
）
5-1 will be displayed.
（
3
）
When save the settings, push the ▲ or ▼ key, move the cursor to
the “1 Save”, and Push the / Phase key.
（
4
）
After completing the settings saving,
“
Completed
”
message will be
displayed. Push the /Phase key.
（
5
）
Return to the operation mode.
1 Save → Save settings and return to
the operation mode.
2 Not Save → Discard the changes and
return to the operation mode.
3 Cancel → Continue the setup.
*Full load is calculated by following formula. (Full load)
＝
(Primary voltage) x (Primary current) x (Coefficient) / 1000[kW]
*1: In case 3P4W, apply the not phase voltage but line voltage as primary voltage.
*2: Coefficient is varies according to the phase wire system. 1P2W → 1, 3P3W/3P4W →1 .73
*If you change a settings, please push the / Phase key and be sure to determine changes. If without determine, the changes will be discarded.
*
*
The underline means the default of setting. After you have been set, even if a power failure occurs does not disappear setting.
you want to set the other circuit, push the Circuit key on the "Setup" screen (1-1), select the circuit, make the setting.
7.2.3 Communication setup
－
the settings for the MODBUS communication
（
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB only
）
Screen Operation Note
1 Transition to the setup mode
1-1.
（
1
）
Push the Setup key in operation mode.
（
2
）
1-1 will be displayed.
（
1
）
Confirm that the cursor focuses the “3 COM.”, push the / Phase key.
（
2
）
2-1 will be displayed.
2
Setup
MODBUS address
（
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB
）
2-1.
（
1
）
In 2-1, Push the ▲ or ▼ key, and move the cursor to the ”1 Address”.
（
2
）
Push the / Phase key.
（
3
）
2-2 will be displayed.
[Address]
：
001
～
255
2-2.
（
1
）
Push the ▲ ▼
＋ －
key, and change the address.
（
2
）
Push the / Phase key,and confirm the setting value.
（
3
）
2-1 will be displayed.
3 Setup the baut rate
（
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB
）
3-1.
（
1
）
In 3-1, Push the ▲ or ▼ key, and move the cursor to the ”2 Baut rate”.
（
2
）
Push the / Phase key.
（
3
）
3-2 will be displayed.
[Baut rate]
：
2400
⇔
4800
⇔
9600
⇔
19200
⇔
38400
⇔
3-2
. （
1
）
Push the
＋
or
－
key, and select the baut rate.
（
2
）
Push the / Phase key.
（
3
）
3-1 will be displayed.
4 Setup the parity
（
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB
）
4-1.
（
1
）
In 4-1, Push the ▲ or ▼ key, and move the cursor to the ”3 Parity”.
（
2
）
Push the / Phase key.
（
3
）
4-2 will be displayed.
[Parity]
：
Non
⇔
Even
⇔
Odd
⇔
4-2.
（
1
）
Push the
＋
or
－
key, and select the parity.
（
2
）
Push the / Phase key.
（
3
）
4-1 will be displayed.
5 Setup the stop bit
（
EMU4-BM1-MB, EMU4-HM1-MB, EMU4-LG1-MB
）
5-1.
（
1
）
In 5-1, Push the ▲ or ▼ key, and move the cursor to the ”4 Stop bit”.
（
2
）
Push the / Phase key.
（
3
）
5-2 will be displayed.
[Stop bit]
：
1
⇔
2
⇔
5-2.
（
1
）
Push the
＋
or
－
key, and select the stop bit.
（
2
）
Push the / Phase key.
（
3
）
5-1 will be displayed.
6 Save the settings
6-1.
（
1
）
After setting all of the items, push the Setup key.
（
2
）
6-1 will be displayed.
（
3
）
When save the settings, push the ▲ or ▼ key, move the cursor to
the “1 Save”, and Push the / Phase key.
（
4
）
After completing the settings saving,
“
Completed” message will be
displayed. Push the /Phase key.
（
5
）
Return to the operation mode, and it will be displayed electric energy screen.
1 Save → Save settings and return to
the operation mode.
2 Not Save → Discard the changes and
return to the operation mode.
3 Cancel → Continue the setup.
*If you change a settings, please push the / Phase key and be sure to determine changes. If without determine, the changes will be discarded.
*The underline means the default of setting. After you have been set, even if a power failure occurs does not disappear setting.
*If you want to set the other circuit, push the Circuit key on the "Setup" screen (1-1), select the circuit, make the setting.
[COM.]
1 Address
2 Baut rate
3 Parity
[Address]
0 01
[Setup]
1 Measure
2 I/O
3 COM.
[Baut rate]
19200 bps
[COM.]
1 Address
2 Baut rate
3 Parity
[Parity]
Even
[COM.]
1 Address
2 Baut rate
3 Parity
[Stop bit]
1
[COM.]
2 Baut rate
3 Parity
4 Stop bit
Quit Setup
1 Save
2 Not Save
3 Cancel
Quit Setup
1 Save
2 Not Save
3 Cancel
If