Mitsubishi Electric CITY MULTI PMFY-P06NBMU-E Technical & Service Manual Download Page 15

Page: 15 / 42

MICROPROCESSOR CONTROL

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK

DAY

MONITOR/SET

CLOCK

ON/OFF

ûFûC

ERROR CODE

AFTER

TIMER

TIME SUN MON TUE WED THU FRI SAT

ON
OFF

Hr
AFTER

FILTER

FUNCTION

ONLY1Hr.

WEEKLY

SIMPLE

AUTO OFF

INDOOR UNIT CONTROL
8-1. COOL OPERATION

<How to operate>

Press POWER ON/OFF button.

Press the operation MODE button to display COOL.

Press the TEMP. button to set the desired temperature.

NOTE

: The set temperature changes 2°F when the or button is

pressed once. Cooling 67 to 87°F.

Control modes

Control details

1-1. Thermostat function
• Room temperature

desired tempe 2 °F: Thermo ON

• Room temperature

desired temperature: Thermo OFF

1-2. Anti-freezing control
Detected condition: When the liquid pipe temp. (TH22) is 32

F or less in 16

minutes from compressors start up, anti-freezing control

starts and the thermostat OFF.

Released condition: The timer which prevents reactivating is set for 3 minutes,
and anti-freezing control is cancelled when any one of the
following conditions is satisfied.

Liquid pipe temp. (TH22) turns to be 50

F or above.

The condition of the thermostat OFF becomes

complete by thermostat, etc.

The operation mode becomes a mode other than COOL.

The operation stops.

1-3. Compressor time delay

• 3 minutes minimum off cycle.

By the remote controller setting (switch of 4 speeds)

2. Fan

1. Thermostat function

Remarks

Type

Fan speed notch

[Low], [Medium2], [Medium1], [High]

4 speeds

OC341F

Summary of Contents for CITY MULTI PMFY-P06NBMU-E











































Search results

Summary of Contents for CITY MULTI PMFY-P06NBMU-E

Reviews:

Related manuals for CITY MULTI PMFY-P06NBMU-E

Brands by name

Popular brands

Mitsubishi Electric CITY MULTI PMFY-P06NBMU-E, Technical & Service Manual

Search results

Summary of Contents for CITY MULTI PMFY-P06NBMU-E

Reviews:

Related manuals for CITY MULTI PMFY-P06NBMU-E

Brands by name

Popular brands