Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 User Manual Download Page 31 | Manualshive

Page: 31 / 162

background image

4 SYSTEM CONFIGURATION

4.1 Applicable Systems

29

4

4

SYSTEM CONFIGURATION

This chapter describes system configuration using an IO-Link module.
For CC-Link IE Field Network configuration, refer to the following.



User's manual for the master/local module used

4.1

Applicable Systems

Applicable master station

When using an IO-Link module, use the following products as a master station.

*1 Simple motion modules and interface boards compatible with the CC-Link IE Field Network cannot be used.

Information on "Applicable master station" described above is the ones at the point when this manual was issued.
For latest information, please visit the website of CC-Link Partner Association.
www.cc-link.org

Ethernet cable

Use a general-purpose Ethernet cable compliant with 1000BASE-T.
Consider the operating environment when selecting available cables that satisfy the product specifications.

(1) Personal computer (engineering tool/FDC)

Model

First five digits of serial number

RJ71GF11-T2

No restriction

RJ71EN71

R04ENCPU, R08ENCPU, R16ENCPU, R32ENCPU, R120ENCPU

QJ71GF11-T2

LJ71GF11-T2

NZ2GF12A-60IOLH8

(1)

DeviceDTM

M_CommDTM-IOLink

IODD DTM Configurator

IODD

«
...
29
30
31
32
33
...
»

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Reviews:

No comments

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brand: KAR-TECH Pages: 28

Brand: 2iB Pages: 5

Go!Control Panel

Brand: 2gig Technologies Pages: 78

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 2

Brand: ZKTeco Pages: 6

Brand: Mitsubishi Pages: 16

Brand: SOMFY Pages: 4

Optidrive Elevator

Brand: Invertek Pages: 5

Brand: Techtrol Pages: 4

Brand: Hard Head Pages: 10

Brand: Sames Pages: 84

UNDER CONTROL CP-28

Brand: G-Force Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands