Mitsubishi Electric A800-E Instruction Manual Download Page 27

Page: 27 / 84

(N) Operation via communication and its settings

PARAMETER

2.5.3

MELSOFT / FA product connection



Initial setting

• Set any value from "5000 to 5002, 5006 to 5008" in any of

Pr.1427 to Pr.1429 Ethernet function selection 1 to 3

to select

the MELSOFT / FA product connection for the application. (For how to set the application value, refer to the Instruction
Manual of the device connected via Ethernet.) (Refer to

page 21

• Enter the Ethernet communication network number in

Pr.1424

and the Ethernet communication station number in

Pr.1425

(Refer to

page 25

• Enable the PLC function (

Pr.414 PLC function operation selection



"0 (initial value)") to use FR Configurator2

(Developer). (For the details of

Pr.414

, refer to the Instruction Manual (Detailed) of the FR-A800/FR-F800 inverter.)



System configuration

• Direct connection with FR Configrator2

• Direct connection with GOT

• Connection using a relay station (programmable controller)

FR Configurator2, GOT, or a relay station (programmable controller) can be connected via Ethernet.

Personal computer

(FR Configurator2)

Ethernet cable

Inverter

Ethernet cable

Inverter

GOT

Ethernet cable

Inverter

Relay station

(programmable controller)

Summary of Contents for A800-E





















































































Search results

Summary of Contents for A800-E

Reviews:

Related manuals for A800-E

Brands by name

Popular brands

Mitsubishi Electric A800-E, Instruction Manual

Search results

Summary of Contents for A800-E

Reviews:

Related manuals for A800-E

Brands by name

Popular brands