Mitox 2800 Owner'S Manual Download Page 2

Page: 2 / 27

DESCRIPTION

BLADE

3 Point blade for grass, weed or brush cutting applications.

DRIVE SHAFT

Contains the drive shaft.

THROTTLE TRIGGER

Spring loaded to return to idle when released.

IGNITION SWITCH

Slide switch, forward to run, back to stop.

SAFETY LEVER

Prevents accidental operation of the throttle.

HANDLE

This handle can be adjusted for maximum comfort

HARNESS ASSEMBLY

Fully adjustable for maximum comfort

8 PETROL

CAP

PURGE BULB

Push the purge bulb to remove the air from the fuel system.

FUEL TANK

Contains fuel and fuel filter

AIR CLEANER

Contains replaceable filter

CHOKE

To help in cold starting

STARTER HANDLE

Pull to start the engine

DEBRIS SHIELD

Helps protect the operator from debris

CUT-OFF KNIFE

Cuts the nylon line to the correct length

NYLON CUTTER HEAD

Contains replaceable nylon trimming line

FRONT HANDLE

This handle can be adjusted for maximum comfort

GEARBOX

For attaching a blade or nylon head to

19 REAR

HANDLE

Incorporating

throttle

trigger, switch, and safety lever

HARNESS FIXING POINT

Fixing point to attach the harness

BLADE COVER

Blade cover for transportation

L HANDLE

U HANDLE

Summary of Contents for 2800




























Search results

Summary of Contents for 2800

Reviews:

Related manuals for 2800

Brands by name

Popular brands

Mitox 2800, Owner'S Manual

Search results

Summary of Contents for 2800

Reviews:

Related manuals for 2800

Brands by name

Popular brands