3
Desktop Mounting a 5320e/5330e/5340e IP Phone (See
Figure
)
Turn the phone so that the front faces away from you.
Hold the base unit so that the lower hooks along the flat edge bend toward
the bottom edge of the phone.
Hinge the hooks of the base unit into the notches on the back of the phone
and snap into place as follows:
a) For a high-angle mount, hinge the two lower hooks into the bottom set
of notches and snap the two upper hooks into the middle set of
notches.
b) For a low-angle mount, hinge the two lower hooks into the middle sets
of notches and snap the two upper hooks into the top set of notches.
Wall Mounting on a Wall Plate (NA only) (See Figure
)
Turn the base unit so that the hooks on the flat edge of the base unit bend
toward the top edge of the phone. Hinge the two upper hooks into the top set
of notches and snap the two lower hooks into the middle set of notches on
the back of the phone.
Secure the base unit using two screws. Use #6 (M3.5) coarse thread
washer head screws, 3/8 inches (1 cm) in length.
WARNING:
The screw length MUST NOT exceed 3/8 inches (1 cm). If
washer head screws are unavailable, use #6 (M3.5) flat washer (3/8
inches (1 cm) in diameter).
Plug the phone cord into the wall jack.
Place the base unit on the wall plate post, and then push down until the unit
is firmly seated.
Using your index finger, lift the clip (from the top) located below the hook
switch, turn the clip 180 degrees, and then let the clip snap into place to form
a hook. (The hook keeps the handset in the cradle when the phone is wall
mounted.)
Wall Mounting on a Wall
Select a location away from electrical cables, pipes or other items that could
cause a hazard when inserting screws in the wall.
CAUTION:
Ensure the wall is capable of supporting the weight of the phone. For addition-
al security, it is recommended that you mount the phone on a plywood back-
board. Mitel is not responsible for phones damaged as a result of improper
wall mounting.
Insert two mounting screws 3 1/4 inches (8.25 cm) apart. Allow about 3/16
of an inch (0.5 cm) between the wall and screw heads for mounting the
phone. Use #10 screws 1 to 1.5 inches (2.5 to 4 cm) in length for mounting
screws and anchoring devices suitable for the wall.
Follow the procedure for mounting the phone on the wall plate to complete
the installation.
Notice to Canadian Customers
This Class B digital apparatus complies with Canadian ICES-003.
Notice to U.S. Customers
NOTE:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE:
Changes or modifications not expressly approved by Mitel Networks™
Corporation may void the user’s right to operate the equipment.
The handset provided with this equipment is hearing aid compatible.
This equipment is not for connection to the telephone network or public coin
phone service. It is only for use when connected to Mitel systems.
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING
TEST CALLS TO EMERGENCY NUMBERS
• Remain on the line and briefly explain to the dispatcher the reason for the
call.
• Perform tests during off-peak hours such as early morning or late
evenings.
Notice to Customers in EU Countries
We, Mitel Networks Ltd.
Of, Castlegate Business Park
Portskewett
Monmouthshire
NP26 5YR
UK
Declare that for the hereinafter mentioned product the presumption of
conformity with the applicable essential requirements of
DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT (RTTE DIRECTIVE) AND OF THE COUNCIL
is given.
Mitel \ 5320e/5330e/5340e IP
Any unauthorized modification of the product voids this Declaration.
For a copy of the original signed Declaration of Conformity (in full conformance
with EN45014), please contact the Regulatory Approvals Manager at the above
address.
Notice to Customers in UAE
B
C
TRA
REGISTERED NO:
ER0091723/12
DEALER NO:
0020008/09
TRA
REGISTERED NO:
ER0091721/12
DEALER NO:
0020008/09
TRA
REGISTERED NO:
ER0091722/12
DEALER NO:
0020008/09
Mitel 5320e IP Phone
Mitel 5330e IP Phone
Mitel 5340e IP Phone
