MIRKA 8991000311, Operating Instructions Manual

Page: 316 / 362

• Before use, check that the backing pad is correctly mounted.
• Install the fully charged battery pack into the sander until it locks in place with a click.
Operating instructions
• The tool is intended to be operated as a hand held tool. The tool can be used in any position.
• Select a suitable polishing pad and secure it to the backing pad. Make sure the polishing pad is centered on the backing
pad.
• The polisher can now be activated / turned on and started by pressing the switch trigger.
• The polisher will run and stay in active mode as long as the trigger is pressed. After the trigger is released the polisher
will stop but continue to stay in active mode for a short time before it automatically deactivates / turns off.
• When polisher is in active mode the right LED is green.
• If an intelligent battery is used all three LEDs will flash green for three seconds during startup.
• In active mode the left LED shows the battery status:
Green: Battery charge level is OK.
Flashing green: Battery charge level is below 75%.
Flashing green/red: Battery charge level is below 50%.
Flashing red: Battery charge level or battery health (only available if intelligent battery is used) is under 25%.
Red: Battery voltage too low polisher is not operable.
AROP-B: 4,000–7,000 rpm. The speed can be adjusted between 4,000 and max rpm by adjusting the position of the
trigger. In active mode the max rpm can be adjusted by pressing rpm+ or rpm–, Figure 1. The rpm can be adjusted in
steps of 4,000, 4,500, 5,000, 5,500, 6,000, 6,500 and 7,000 rpm.
ARP-B: 1,500–2,200 rpm. The speed can be adjusted between 1,500 and max rpm by adjusting the position of the
trigger. In active mode the max rpm can be adjusted by pressing rpm+ or rpm–, Figure 1. The rpm can be adjusted in
steps of 1,500, 1,600, 1,700, 1,800, 1,900, 2,050 and 2,200 rpm.
• The rpm can be locked to prevent an accidental rpm change. Wait until the sander is not in active mode. Simultaneously
press and hold both rpm+ and rpm– buttons and then pull the switch trigger. In order to unlock the tool, repeat same
operation. If rpm+ or rpm– is pressed in speed lock mode the right led flashes red twice but no speed change occur.
• When polishing, always place the tool on the work surface before starting the tool. Always remove the tool from the
work surface before stopping it. This will prevent gouging of the work surface due to excess speed of the polishing
pad.
• When polishing is finished, remove the battery from the polisher by simultaneously pressing the button on both sides
and removing the battery from the tool. Charge the battery.
Bluetooth
This tool is equipped with Bluetooth® low energy technology and can be connected to an app from which additional
tool functionality can be accessed. For more information on the app functionality and if it is available in your country, go
to www.mirka.com/mymirka
Activate Bluetooth on your Mirka
®
ARP-B 300NV & Mirka
®
AROP-B 312NV as follows:
1.
Connect the battery to the tool.
2. Press and hold the rpm+ button while activating the tool by pressing the switch trigger.
3.
Middle LED is flashing green, to indicate that Bluetooth is active and ready for connections.
4. Middle LED is lit green when the tool is connected to another Bluetooth device.
5.
Bluetooth is deactivated when the tool is deactivated/turned off.
NOTE! If the app is not installed or if it is not available in your country, Bluetooth shall not be activated.
The Bluetooth
®
word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such
marks by Mirka Ltd is under license. Other trademarks and trade names are those of their respective owners.
FCC Rules & Industry Canada’s licence-exempt RSS
Compliance with the radio regulations in North America has been verified in accordance with FCC Part 15 subpart B and
C, RSS-GEN, RSS-247 and FCC §15.247. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
316
Mirka® ARP-B 300NV & Mirka® AROP-B 312NV
en | us-ca