Mircom FR-320 Series Installation And Operation Manual Download Page 50 | Manualshive

Page: 50 / 112

background image

50

Configuration

10.4

Command Menu

The main command menu is shown in

. The first line of the LCD will always show

“-Command Menu-“, and the second line scrolls through different selections. Use the “UP” and

“DOWN” keys to scroll through the menu, and press the

key to make a selection. To exit

from the main command menu, select the “Exit” menu option and then press either the

or

key.

Figure 26 Command Menu

Pressing “LAMP TEST” at any time will show the information about the system and the
software version. The first line shows the panel mode number, pre-programmed mode and the
information if the panel has a dialer or not. The second line shows the software version
number. The version of the software is read as Major.Minor.Revision.

Note:

Command Menu Item 1 and 6 can only be accessed if jumper JW6 is placed on
the main board.

X

i

Access level Required

Configuration

Configuration

Configuration

Command

Command

Command

Configuration

Command

Command

«
...
48
49
50
51
52
...
»

Summary of Contents for FR-320 Series

















































































































Reviews:

No comments

Related manuals for FR-320 Series

Relion 670 series

Brand: ABB Pages: 760

Brand: ABB Pages: 128

Brand: D-Link Pages: 40

Brand: Raymarine Pages: 12

Brand: Jafar Pages: 13

Brand: IBM Pages: 105

Brand: YASKAWA Pages: 256

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: Jafar Pages: 10

Brand: Kasco Pages: 3

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Q Module WFZ16.Ox

Brand: QUNDIS Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands