Mircom DACT-100A, Installation And Operation Manual

Page: 11 / 20

Page 9
Items accessible to Level II only
ITEM
Number
Access
Level Menu Category Menu Label Description
30 II Account (#1) Account ID #1 Assign 4-6 numeric Account ID to be identified with Account #1
monitoring station receiver.
31 II Account (#1) Dial-Prefix #1 (OPTIONAL) Set up-to-8-digits to be first dialed by DACT when
attempting to call Account #1 monitoring station receiver.
32 II Account (#1) Local Number #1 Set up-to-8-digits to be dialed (after Dial-Prefix #1 digits) by DACT
when attempting to call Account #1 monitoring station receiver.
33 II Account (#1) Report Format #1
Default Contact ID Choose report format (Contact ID or SIA) to be generated by DACT
when reporting with Account #1 monitoring station receiver.
40 II Account (#2) Account ID #2 Assign 4-6 numeric Account ID to be identified with Account #1
monitoring station receiver
41 II Account (#2) Dial-Prefix #2 (OPTIONAL) Set up-to-8-digits to be first dialed by DACT when
attempting to call Account #2 monitoring station receiver.
42 II Account (#2) Local Number #2 Set up-to-8-digits to be dialed (after Dial-Prefix #2 digits) by DACT
when attempting to call Account #2 monitoring station receiver.
43 II Account (#2) Report Format #2
Default Contact ID Choose report format (Contact ID or SIA) to be generated by DACT
when reporting with Account #2 monitoring station receiver.
50 II Report Priority ALARM Events
Default is
Account 1
Choose which Account # (1 or 2) will be the first to be attempted to be
reached by the DACT, when an ALARM event is to be reported. This
is designated as the “primary
” account and the other will become the
“secondary”. If the DACT cannot report to the primary, it will then
attempt to report to the secondary. This cycle will normally continue
until the event is eventually or the <MAXIMUM Attempts> has been
achieved.
51 II Report Priority TROUBLE Events
Default is
Account 1 Choose which Account # (1 or 2) will be the first to be attempted to be
reached by the DACT, when a TROUBLE event is to be reported.
(See ITEM 50 for a description of the DACT report-attempt
operation).
52 II Report Priority SUPERVISORY
Events
Default is
Account 1 Choose which Account # (1 or 2) will be the first to be attempted to be
reached by the DACT, when a SUPERVISORY event is to be
reported. (See ITEM 50 for a description of the DACT report-attempt
operation).
53 II Event Logging Ignore <SUPVSRY>
Events,
Default will Report
Supervisory This selection allows the overriding of the “normal’ reporting of the
supervisory events when set to 1. The DACT will report supervisory
events when set to 2.
55 II Report Priority Max. Attempts
Range is 5 to 10,
Default is 6
Attempts Set the “normal” upper limit for DACT attempts (call-attempt pairs) to
report to monitoring station receivers.(See ITEM 50 for a description
of the DACT report-attempt operation). After this count has been
exceed, the DACT will assert the TROUBLE-SEND signal (and
BUZZER) to the connected Fire-Panel.
60 II Phone Line (1/2) Dial-type Line 1 Configure Line 1 for DTMF (Tone) or Rotary (Pulse) Dialling.
61 II Phone Line (1/2) Dial-type Line 2 Configure Line 2 for DTMF (Tone) or Rotary (Pulse) Dialling.
62 II Configuration Reboot DACT Test watchdog circuit by (1) halting program execution and (2) waiting
for watchdog to reset DACT.
63 II Phone Line(1&2) Deaf Dialling
Default dial tone(1) To wait and listen for dial tone select 1 (default) or Ignore Dial Tone
for use with “Cellular Telephone” select 2
64 ll Phone Line 2 Set Testing Date Default testing date for Phone Line 2 is the 1
st
day of the month.
Selection can be made from 1
st
to 28
th
day of the month. Whenever
Line 2 is used for a cellular phone, then the Deaf Dialling should be
set to 2 (63
set to Ignore Dial Tone).
NOTE: All configurable items have default values assigned by the “Restore-to-Default” operation. All items must have a (non-zero) value
assigned unless specifically identified as OPTIONAL within the table(s) above.