background image

(4) Click on the left button of format then show the Figure 31 and 

F

i

gure32, if the SD card is at

 4

G or below 4

G,

file system  should 

be choose 'FAT','distribut the unit size'  should be choose 6 4 K 
(Figure 36); if the SD card is the 8 G or above 8G,'file syste should 
be choose 'FAT 3 2', 'distribut the  unit size' should be shoose 3 2 K 
(Figure 37) press the "

O

K"’

 

button began to identify format.

'

'

(5) If the SD card is the 4G or below4G,there will show a dialpg ,press 

the"OK"button to show the Figure38, then press the  'OK 'button  
start to format; If the SD card is the 8G or above8G , there will 
show the Figure 39 , And then press the'OK'

 

button start to

      format .  

Figure 36

Figure 37

Figure 38

19

Rules

1.  Not allow to inset or take out the SD card when the video recorder is 

working,if do that  must according to  the normal  shutdown  
recorder and then inset or take out the SDcard , because SD card is 
very easy to damage and loss of the machine program.
2. The proposed use of each card after the inspection,reformat the 
SD card again.

 

3. Attention to the SD card format correctly operation, as detailed in 

the SD card format operation.

4. In accordance with the provisions of the original SD card, SD card to 

protect the appearance of the plastic shell can not draw trace badly, 
otherwise the manufacturer don’t supply warranty.

二、

System

 

element

Host System                  

     

Camera  

  

 

             

SD

 

Card

三、

Equipment systems

 

installation and testing

3-1 Mainframe fixed 

Shown in Figure 2, the host at the bottom of the 
groove with double-sided adhesive paste to  
quakeproof.In the vehicle to find a relatively 
stable temperature, water is’t easy to reach, 
close to the instrument panel, ventilation, with 4 
screws will be fixed host, and truss video 
recorder bus with tie. 

3-2  The installation of cameras

Shown in Figure 3, installation of cameras, 
requirements of the first camera to carry out 
wiring, as far as possible all the camera signal 
line wiring in the interior of vehicle, should not 
be exposed or visible camera signal line place.

Figure 2

Figure 3

02

Figure 1

Summary of Contents for MDVR-301













Reviews: