manualshive.com logo in svg

Miranda Densite IRD-3111, Manual To Installation And Operation, Page: 24 / 60

Share
Download
Miranda Densite IRD-3111 Manual To Installation And Operation Download Page 24

GUIDE TO INSTALLATION AND OPERATION 
 

3.4.7.1  AFD tab 

 

Mode 

Use the AFD Mode pulldown to select the operating mode 

•

 

Auto 

•

 

Manual 

 

Config 

 
Use the 

Insertion

 pulldown to select whether AFD 

information will be inserted in the output. 

•

 

OFF 

•

 

AFD 

 

Insertion Line:  

The Insertion line is used to select on which 

line in the VANC the AFD packet (SMPTE 2016) will be 
inserted. It is not necessary to specify the detection line 
since the card will automatically detect the incoming packet. 
 

Default settings 

 
The 

Default

 data box shows the default AFD code to be 

used if no valid AFD code is detected at the input (AUTO), or 
the AFD that is always used (MANUAL) 

 

Change:

  Click the 

Change…

 button to open the 

Select AFD

 

panel showing the available AFD codes that could be used 
as the default. Click on one to select it, then click 

Apply

 or 

OK

 at the bottom of the panel. 

 
Flags 

 
This section gives information about AFD flag management. 
 
Presence – the status icon is green if AFD flags are detected in the input data 
stream 
 
Detected – the data box shows the AFD code for the detected flags 
 
Inserted – the data box shows the code of the AFD inserted in the output data 
stream 
 

 
Aspect Ratio Scaling Mode 

 
Use the pulldown to select the aspect ratio scaling mode that will be used. 
These options are available: 

•

 

OFF 

•

 

Auto 

•

 

Stretch 

•

 

Center Cut 

•

 

Letter box 

•

 

Pillar box 

Figure 3.10  Select AFD panel 

Figure 3.9  Video Output panel – AFD tab 

20

  |  IRD-3111 

Summary of Contents for Densite IRD-3111





























































Reviews:

No comments