manualshive.com logo in svg

Mipex MIPEX-02 Series, User Manual, Page: 43 / 46

Share
Download
Mipex MIPEX-02 Series User Manual Download Page 43

 

Optosense LLC 

USER MANUAL 

Design department 

SMALL-SIZE EXPLOSIVE GAS MEASURING 

SENSOR MIPEX-02-X-X-X.1 X (RX) 

 

ESAT.413347.005 UM 

Revision 3.0 

January 19th, 2017 

Page 43 of 46 

THE SOLE PROPERTY OF OPTOSENSE LLC. ANY REPRODUCTION WITHOUT THE WRITTEN PERMISSION OF OPTOSENSE LLC IS PROHIBITED. 

 

APPENDIX E. DUST FILTER ATTACHING 

To improve sensor operation reliability, dust filter should be attached to sensor surfaces. For 

sensor housing types “1” and “3”, only top filter (ESAT.717100.001; see Fig. 20) should be applied. 
For housing 

type “2” side filter (ESAT.717100.002; see Fig. 21) should be attached as well. Filters 

material  is  fluoroplastic 

membrane  “Vladipor  MFFC  TC  6-55-221-1413-2004”.  On  the  filter 

backside 

there  is  an  adhesive  layer  “3M  Double  Linered  Laminating  Adhesive  7952”  in  hatched 

areas in Fig. 20 and Fig. 21. 

 

Fig. 20. Top filter dimensions 

 

 

Fig. 21. Side filter dimensions 

Perform the following steps to attach dust filter: 

 

 

Perform this work in a well-illuminated and well-ventilated area. 

 

Once  a  dust  filter  is  attached  to  sensor  surface,  perform  zeroing  procedure 
(see Appendix D.1 for details). 

1.  Degrease  surface  of the  up

per side of sensor. For housing type “2”, perform the same 

operation on the side surface. 

2.  Extract filter from the packing and remove its substrate with tweezers. 

3.  Align the filter exactly to the center of the upper side of sensor with tweezers  and then 

press on it. For 

housing type “2” perform the same operation on the side surface. 

Summary of Contents for MIPEX-02 Series















































Reviews:

No comments