Mipex MIPEX-02 Series User Manual Download Page 18 | Manualshive

Page: 18 / 46

Mipex MIPEX-02 Series User Manual Download Page 18

Optosense LLC

USER MANUAL

Design department

SMALL-SIZE EXPLOSIVE GAS MEASURING

SENSOR MIPEX-02-X-X-X.1 X (RX)

ESAT.413347.005 UM

Revision 3.0

January 19th, 2017

Page 18 of 46

THE SOLE PROPERTY OF OPTOSENSE LLC. ANY REPRODUCTION WITHOUT THE WRITTEN PERMISSION OF OPTOSENSE LLC IS PROHIBITED.

6.6. Low power consumption mode

It is possible to switch sensor to low power consumption mode, which corresponds to

indicator mode. To switch sensor power consumption mode, resetting its power supply is not
necessary. Use the following commands to control power consumption mode (see Appendix
C.2.6):



<LOWPW1> switches on low power consumption mode.



<LOWPW0> switches off low power consumption mode.



<LOWPW?> returns status of low power consumption mode.

While low power consumption mode is active:



P

ower consumption ≤ 1.8 mW.



Sensor performance decreases by not more than 2 times.



Current pulse repetition period increases to 40

± 20 % ms.



Sensor’s compliance with metrological characteristics stated in Table 3 is not
guaranteed.

«
...
16
17
18
19
20
...
»

Summary of Contents for MIPEX-02 Series















































Reviews:

No comments