MINN KOTA 1854051, Manual

Page: 1 / 24

1 | minnkotamotors.com ©2022 Johnson Outdoors Marine Electronics, Inc.
MKA-51 ELECTRIC-STEER
QUICK RELEASE BRACKET
1854051
TOOLS AND RESOURCES REQUIRED
Item /
Assembly
Part # Description Qty.
A (Items 2-10) 2994936 BAG ASM, ES SLIDING QRB 1
2 2223446 SCREW-1/4-20 X 2" PFH SS 6
4 2373484 SCREW-1/4-20 X 7/8 PFH SS 6
6 2263103 NUT-1/4-20 NYLOCK SS 12
8 2261713 WASHER-1/4 FLAT 18-8 SS 6
10 2371712 WASHER-FLAT 9/32 X 5/8 X 1/16 6
B (Items 12-16) 2771998 BOTTOM PLATE KIT, MKA-51 QRB 1
12 2381958 PLATE-BOTTOM, QRB, MACH 1
14 2228413 CAM PUCK, MACHINED, ES QRB 1
16 2373428 SCREW-5/16-18 X 3/4" PFH SS 1
C (Items 18-40) 2771997 TOP PLATE KIT, MKA-51 QRB 1
18 2381956 PLATE-TOP, QRB, MACH 1
20 2373611 DRAWBAR, ES QRB 1
22 2222716 SPRING,COMPRESSION OD.480 1
24 2373260 STOP, DRAW BAR 1
26 2383431 SCREW-#12 X 5/8 TYPE B PFH SS 2
28 2225110 PAD, URETHANE,QCK ATTACH 1
30 2381948 EXTRUSION BACKER, MACH, ES QRB 1
32 2228415 CAM ARM, QCK ATTACH PLATE 1
34 2262635 PIN-ROLLER, S/S 1
36 2372623 PIN W/RING, QRB 1
38 2373650 LANYARD ELECTRIC STEER,QRB 1
40 2372644 PIN-ROLL, .093 x 5/8" SS 1
p
2377169 MANUAL, ELEC.STEER SLIDING QRB 1
p
2225615 DECAL-WARNING,MNT PLATE 1
40 40
30 30
28 28
22 22
38 38
18 18
26 26
14 14
16 16
12 12
32 32
34 34
36 36
24 24
20 20
2 2
6 6
10 10
8 8
4 4
• #3 Phillips Screwdriver
• Drill • 9/32” Drill Bit
• Awl or similar marking tool • 7/16” Box End or
Open End Wrench
• A second person to help
with the installation
C C
B B
A A
Compatible with Minn Kota® Freshwater Electric-Steer Trolling Motor models, including the Ulterra™, Terrova®, PowerDrive™, PowerDrive V2 and DeckHand 40.
MOUNTING CONSIDERATIONS
It is recommended that the motor be mounted as close to the
centerline or keel of the boat as possible. The motor must not
encounter any obstructions as it is lowered into the water or raised
into the boat when stowed and deployed. Make sure the motor rest
is positioned far enough beyond the edge of the boat. Make sure the
area under the mounting location is flat, clear to drill holes and install
nuts and washers.
p
Not shown on parts diagram.
NOTICE:
The mounting surface for the Bottom Plate must
be completely flat. Rubber Washers can be used to shim
the Bottom Plate flat before hardware is tightened. The
Top Plate will not fit correctly unless the Bottom Plate is
installed completely flat.