background image

8 / 10

FHK34, 908143

AMX5000

Short instruction

Commissioning

 

When commissioning the AMX5000, it is necessary to perform
an initial reset in order to collect basic data (e.g. connected
sampling pipe, motor data). An initial reset also performs an au-
tomatic adjustment of the airflow monitoring on the connected
sampling pipe(s).
If the AMX5000 is operated within the system limits without
“HELIOS PipeCalc” calculation, commissioning with the 

“Ea-

syConfig” method

 can be carried out directly on the

AMX5000. 
For projects in which the “HELIOS PipeCalc” calculation soft-
ware was used or in which customer-specific adaptations have
to be made in the device configuration, the 

“HELIOS Config”

configuration software has to be used. 

Starting up

 

Before the AMX5000 is switched on, it is absolutely
necessary that all of the required measures have
been performed (see FHB 34 (908142), section 7.1). 

• sampling pipe correctly mounted and connected

to the AMX; 

• smoke sensors and expansion modules installed in
   the AMX and connected;

• isolation strip on the Lithium battery (MAIN
   BOARD) removed.

Sequence and procedure for starting up:

 

1.

Switch on supply voltage (FACP); while the fan accelerates
incrementally to its final speed (takes about 100 s), the next
procedure can be carried out. 

The system is immediately

armed for alarm.

2.

“EasyConfig”: 

select necessary switch setting for operati-

on according to 

“System limit table”

 (e.g. 

“b2”

 see

“Re-programming”

.

- or:

“HELIOS Config”:

 after adapting the configuration (alarm

threshold according to “HELIOS PipeCalc” and other crite-
ria in Tables A and B), select switch setting 

“X01”

, “X02"

or 

“X03”

.

3.

Set date and time via MAIN BOARD with “EasyConfig” or
from “HELIOS Config” (adoption by PC).

4.

Following a 

minimum waiting time of 5 min

 after swit-

ching on, an initial reset must be performed (possible only
via MAIN BOARD) 



see 

“Initial reset”

.

5.

The AMX5000 is now ready for operation. 

Re-programming

Example: Response class B, system limit 2, AMX5102 (2 sam-
pling tubes), required switch setting

 b22

.

Initial reset

Measurements / commissioning protocol

Carry out the following measurements: 
• Measure operating voltage on terminals 1 (+), 2 (-) (if redun-

dant supply, then also terminals 3 & 4) 



target value = 12.3

to 13.8 VDC (in 12 VDC operation) or 21.6 to 27.6 VDC (in
24 VDC operation).

• Airflow values in switch settings 

V

 (see Technical Description

FHB 34 (908142), section 7.6.1) 

• The commissioning protocol is like a personal history of the

AMX5000 and should therefore be filled out conscientiously
and completely and stored in the AMX5000. If required, a
copy can be made and stored in the installation dossier. 

Measure

Display /
indication

Procedure
Remark

Switch settings 

W01

 to 

W48

 may be used only after 

consulting with the manufacturer. The configured 
values they contain concerning airflow monitoring 
are 

not

 tested in accordance with EN (or NFPA). 

6.

Press the "UP” 
button

Flashing 

C32

•  Display of the default

    setting

7.

Press "UP” 
twice until dis-
play shows 

b

In sequence:

A / b

•  Display switch setting

    group 

b

8.

Press the "OK" 
button

b11 

•  Display of the smallest
  possible setting in group
  

b

9.

Press "UP” 
until display 
shows 

b22

In sequence:

b11 / b12 / b21 
/ b22
 

•  Display of the possible
   settings in group 

b

10.

Press the "OK" 
button

Flashing  

b - - 

(approx. 4 x)

•  New setting is pro-
   grammed 

11.

Check: Press 
the "UP” button

Flashing 

b22

•  Display of the new set-
   ting

Measure

Display /
indication

Procedure
Remark

Before performing an initial reset after switching on 
the AMX5000, a 

waiting time of at least 5 min

 

must be observed.  

1.

Press the "UP” 
button

Flashing 

C32 

or other

•  Display of the default

    setting or the installa-
    tion-specific switch set-
    ting

2.

Press "UP” 
several times 
until display 
shows 

U

In sequence:

A to U

•  Display of the switch

    setting group 

U

3.

Press the "OK" 
button

U01 

•  Display initial reset On

4.

Press the "OK" 
button again

Flashing 

U - -

 

(5 to max. 120 
s)

 

•  Initial reset runs

5.

Wait

Flashing  point

 

(watchdog indi-
cator)

•  Initial reset completed 

 

 

 

Summary of Contents for AMX5000 Series











Reviews: