14
allowing you to monitor your baby or the area you
wish to monitor continuously.
· VOX mode ON: The camera only transmits when it
detects a sound with sufficient intensity, according to
the level selected, around the camera.
To activate this function, first of all make sure you
have set the standby mode to 1/3 or 5 minutes (see
point
5.2.8.1.
). Choose 1/3 or 5 if you want your
camera to stop transmitting the image after 1/3 or 5
minutes if there is no sound around.
Once the standby time is set, to activate VOX mode,
please, follow the next instructions:
1. Press the Menu/Back
key and the menu will
pop up.
2. Press UP or DOWN key to select VOX icon then
press
key enter into the sub-menu.
3. Press UP /DOWN key to select the VOX
option: OFF/ON
4. Press
key to save the setting.
5. Press the Menu/Back
key to return to the main
screen.
6. VOX icon (D) will be displayed at the top of the
LCD screen.
Note:
If the device is in VOX mode and you do
not wish to wait 1, 3 or 5 minutes for the screen to
turn itself off, press the ON button (10) to turn it on
immediately.
5.2.8.3. TRANSMISSION LEVEL
On this menu you can change the power level
transmitted by the camera, choosing from amongst
the high/low options. When at the high position (HI),
coverage will extend 250 meters in open country with
the original power. When at the low position (LOW),
the maximum transmission distance is reduced to
around 120 meters in open country as the transmitting
power is reduced.
To configure the transmission level, follow the next
steps:
1. Press the Menu/Back
key and the menu will
pop up.
2. Press the UP key or DOWN key until the
transmission level menu icon is highlighted then
press the
key.
3. Using the UP key or DOWN key, select the
transmission level desired: HIGH or LOW.
4. Confirm the selection pressing the
key.
5. Press the Menu/Back
key to return to the main
screen.
6. TRANSMISSION LEVEL icon (E) will be displayed
at the top of the LCD screen.
5.2.8.4. CAMERA MENU
5.2.8.4.1. CHOOSING THE CAMERA
This product is designed to allow the observation of
different areas with up to 4 cameras. To choose the
camera you want to see, follow the next steps:
1. Press the Menu/Back key
and the menu icon
will pop up;
2. Press the UP or DOWN key until the camera
icon is highlighted then press
key
to enter into the sub-menu.
ENGLISH
3. Press UP /DOWN key to select the desired
camera to view (Camera 1, camera 2, camera 3,
camera 4 or scan mode).
4. Press
key go to selected cam.
Note 1:
You will only be able to select the cameras
that have already been paired with the
monitor.
Note 2:
There is a faster way to change the camera
you are viewing. Directly press
key to cycle
through paired cameras: CAM1 / CAM2 / CAM3 /
CAM4 / SCAN MODE.
5.2.8.4.2. SCAN MODE
This function automatically cycles through your paired
camera channels to display each camera for 12
seconds. This function can be used only when you
have more than 1 camera unit paired.
To enter in this mode:
1. Press the Menu/Back
key and the menu will
pop up.
2. Press the UP key or DOWN key until the
camera icon is highlighted then press
key enter into the sub-menu.
3. Press UP /DOWN key to select the scan
camera icon .
4. Press key.
Note 1:
When one of the cameras is out of range or is
not switch on, the monitor will warn you and the Scan
Mode will stop.
Note 2:
The Scan mode can be turned on or off by
pressing the
button while viewing the main screen.
5.2.8.5. ADD CAMERA AND PAIRING
The pairing between the monitor and the camera will
be done under two circumstances:
- If you want to add an additional camera.
This product is designed to allow the observation of
different areas with up to 4 cameras.
- If the monitor and the camera are not paired.
The monitor and the original camera leave the
factory with channel 1 programmed,
nonetheless, if for some reason, they are not, you
can link them manually following the steps
indicated below.
To pair the camera and the monitor follow the next
steps:
1. Press the MENU/Back
key and the menu will
pop up.
2. Press UP key or DOWN key to select ADD
camera icon
then press
key enter into the
sub-menu.
3. Press UP /DOWN key to select the desired
camera to add.
4. Press
key to search for a camera unit. The
power LED indicator (2) will begin to flash in green.
5. While the LED indicator is flashing, press the link
button on the camera (VI).
6. Once paired, the LED indicator will stop flashing
and the image of the camera will show immediately
on the monitor unit screen.
7. If unsuccessful, please repeat above steps.
For various reasons you may lose the connection
between the monitor and a camera which is already
