5
MAINTENANCE
the tool, battery pack and charger to a
service facility for:
1. Press and hold the backup release valve to ensure
the tool has reset.
2. Remove the battery pack.
3. Remove the jaws from the tool.
4. Use a soft mallet to tap the rear of the jaws to
release.
5. Clean any dirt and debris from the blades before
starting another cut.
Cutting Tips
Cut farther in from the end of the material to avoid
crooked cuts.
Do not attempt angled cuts. It will damage the
blades. Hold the material squarely between the
blades.
Cut clean material to extend the blade life. Wipe dirt
and debris from material and blades before begin-
ning the cut.
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
When us
ing
the ACSR jaws, ensure the blade
retainer is installed.
Backup Release Valve
If the jaws need to be opened without completing the
cycle, press and hold the backup release valve. Hold
tool securely until the cylinder retracts fully.
Jammed Blades
Dirt and debris can cause the blades to become
jammed together after a cut. If the tool shuts off and
the blades are still closed:
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE
®
service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good re-
pair by adopting a regular maintenance program. Af-
ter six months to one year, depending on use, return
MILWAUKEE
®
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
Hydraulic Fluid
To extend the life of the tool, return the tool to a
MILWAUKEE
®
service facility for hydraulic fluid
replacement after 20,000 cuts or 2 years of use.
Lubrication
Mechanical inspection and cleaning (gears, spin-
dles, bearings, housing, etc.)
Electrical inspection (battery pack, charger, motor)
Testing to assure proper mechanical and electrical
operation
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE
®
service facility for repairs.
Jaws and Blades
Inspect jaws for cracks or damage. Do not use dam-
aged jaws. Replace the blades when they become
dull, rounded, chipped, or damaged.
battery pack before
-
-
WARNING
Always remove
changing or removing accesso
ONE-KEY™
mended for this tool. Others may be hazardous.
your tool, battery pack or charger in liquid or
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to the nearest service centre.
ACCESSORIES
1. Remove the battery pack.
2. Remove the screw and open the battery door.
3. Remove the old battery, keep it away from
children, and dispose of it properly.
4. Insert the new battery (3V CR2032), with the
positive side facing up.
5. Close the battery door and tighten the screw
securely
Refer to the ONE-KEY App for information regarding
necessary servicing, such as internal battery life and
crimp count.
WARNING
Chemical Burn Hazard.
This device contains a
lithium button/coin cell battery. A new or
used battery can cause severe internal
burns and lead to death in as little as 2
hours if swallowed or enters the body. Always
secure the battery cover. If it does not close
securely, stop using the device, remove the batter-
ies, and keep it away from children. If you think
batteries may have been swallowed or entered the
body, seek immediate medical attention.
Internal Battery
An internal battery is used to facilitate full
ONE-KEY™ functionality.
To replace the battery:
For a complete listing of accessories, go online to
milwaukeetool.com.au or milwaukeetool.co.nz or
contact a distributor.
DO NOT cut any other materials with the
Copper/Aluminium jaws other than what is
specified in this document. DO NOT cut copper
with the ACSR jaws. It will damage the blades and
jaws and potentially the tool.
Ensure only one blade has the retainer installed. If
two blade retainers are installed, this will put the
user at risk of injury.
