3
Attaching and Removing Accessories
1/4" Hex Impact Driver
(M18 FID)
This impact driver is intended for use
with drill and driver bits.
1. To attach an accessory, press the
shank into the hex drive chuck.
2. To remove the accessory, pull out
the ring and remove the accessory.
Release the ring.
Square Drive Impact Wrenches
(M18 FIWF12)
1. Use only the appropriate size Square Drive
Sockets.
2. To attach a socket, align the accessory with the
anvil and push it
fi
rmly over the retaining ring.
3. To remove the accessory, pull the accessory
off the anvil.
Square Drive Impact Wrench with Pin Detent
(M18 FIWP12)
1. Use only the appropriate size Square Drive
Sockets.
2. To attach a socket, align the hole in the acces-
sory with the detent pin on the anvil. Hold the
detent pin in while pushing the socket onto the
anvil. The detent pin will snap into place in the
hole to secure the socket.
3. To remove the socket, insert a nail or other thin
object into the hole in the accessory and press
in the detent pin. Pull the accessory off the anvil.
ASSEMBLY
WARNING
Recharge only with the
charger speci
fi
ed for the battery. For speci
fi
c
charging instructions, read the operator’s
manual supplied with your charger and battery.
Inserting/Removing the Battery
To
remove
the battery, push in the release buttons
and pull the battery pack away from the tool.
To
insert
the battery, slide the pack into the body of
the tool. Make sure it latches securely into place.
WARNING
Use only sockets and other
accessories speci
fi
cally designed for use on
impact wrenches and drivers. Other sockets
and accessories might shatter or break caus-
ing injury.
WARNING
Always remove battery
pack before changing or removing acces-
sories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
OPERATION
WARNING
To reduce the risk of injury,
wear safety goggles or glasses with side
shields.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
1. For
forward
(clockwise)
rotation, push the control
switch in the direction
shown. Check the direction
of rotation before use.
2. For
reverse
(counterclockwise) rotation, push
the control switch in the direction shown. Check
the direction of rotation before use.
3. To
lock
the trigger, push the control switch to the
center position. The trigger will not work when
the control switch is in the locked position.
Always remove the battery pack before perform-
ing maintenance, changing accessories, storing
the tool and any time the tool is not in use.
Selecting Speed
Allow the tool to come to a complete stop before
changing speeds. Press the selector button
to
cycle between the settings.
CENTER TO LOCK
Forward
Reverse
Setting
Max RPM
/
M18 FID
M18 FIWF12
M18 FIWP12
†
M18 FID: The
function is designed to reduce
screw stripping, screw breakage, and damage
to the work surface when driving self-tapping
screws. This function is optimized for the most
common materials, including #8-#10 self-tapping
screws between ½”-1” in length and 20-28 gauge
sheet metal.
††
M18 FIWF12 / M18 FIWP12:
function is designed to give the user
greater control in application and reduce damage
to the fastener or work surface by automatically
shutting the tool off after the tool senses the
mechanism impacting for approximately one
2
BATTERY TOOL USE AND CARE
PERSONAL SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WORK AREA SAFETY
ELECTRICAL SAFETY
POWER TOOL USE AND CARE
Keep work area clean and well lit.
Cluttered or
dark areas invite accidents.
Do not operate power tools in explosive atmos-
pheres, such as in the presence of
À
ammable
liquids, gases or dust.
Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operat-
ing a power tool.
Distractions can cause you to lose
control.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodi
¿
ed plugs and matching outlets will
reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
tions.
Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts.
Damaged or entangled cords increase the risk
of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply.
Use of an GFCI
reduces the risk of electric shock.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the in
À
uence of drugs, alcohol or medication.
A
moment of inattention while operating power tools
may result in serious personal injury.
Use personal protective equipment. Always
wear eye protection.
Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carry-
ing the tool.
Carrying power tools with your
¿
nger
on the switch or energizing power tools that have
the switch on invites accidents.
Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
Do not overreach. Keep proper footing and bal-
ance at all times.
This enables better control of the
power tool in unexpected situations.
Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts.
Loose clothes, jewelry or long hair
can be caught in moving parts.
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of
dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles.
A careless action can cause
severe injury within a fraction of a second.
Do not force the power tool. Use the correct
power tool for your application.
The correct power
tool will do the job better and safer at the rate for
which it was designed.
Do not use the power tool if the switch does not turn
it on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands
of untrained users.
Maintain power tools and accessories. Check for
misalignment or binding of moving parts, break-
age of parts and any other condition that may
affect the power tool’s operation. If damaged,
have the power tool repaired before use.
Many ac-
cidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed.
Use of the power tool for operations
different from those intended could result in a hazard-
ous situation.
Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
Recharge only with the charger speci
¿
ed by the
manufacturer.
A charger that is suitable for one type
of battery pack may create a risk of
¿
re when used
with another battery pack.
Use power tools only with speci
¿
cally designated
battery packs.
Use of any other battery packs may
create a risk of injury and
¿
re.
WARNING
Read all safety warnings, instructions, illustrations and speci
¿
cations provided
with this power tool.
Failure to follow all instructions listed below may result in electric shock,
¿
re
and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in
the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
850 2100 3000
1700 2000 2500
Designed for driving
self-tapping screws in
sheet metal
†
2 000 - tool will shut
off after about one
second of impacting
††
1
2
3
The
second.