Page 1
INTENDED USE OF THE TOOL
MADE IN TAIWAN
• Shorter than a credit card at 3.46" long
• Industry leading 415 ft/lbs. of MAX torque
The 1832 is intended to be used for removing and
fastening bolts and nuts with 1/2" drive impact
sockets only. Do not use this tool outside
of the designed intent. Never modify this tool for
any other purpose or use.
Model:
Product Type:
ONYX 1/2" NANO ANGLE IMPACT
WRENCH - 415FT/LB
ONYX 1/2" NANO
ANGLE IMPACT WRENCH
- 415FT/LB
1832
DO NOT DISCARD – GIVE TO USER
WARNING
www.astrotools.com
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
BEFORE USE
Study, understand and follow all instructions
provided with this product. Read these instructions
carefully before installing, operating, servicing or
repairing this tool. Keep these instructions in a safe
accessible place.
PRODUCT INFORMATION:
WARNING
Caution: To help prevent personal injury.
•
Use of this product can expose you to chemicals
including ethylene glycol, gasoline vapors and engine
exhaust, which are known to the State of California to
cause cancer, birth defects, or reproductive harm.
For more information, visit www.P65Warnings.ca.gov.
Always wear ANSI approved safety equipment, safety
glasses and clothing when using this product. Study,
understand, and follow all instructions provided with
this product. Failure to read and follow all warnings and
operating instructions may result in damages and
serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with
accessories not designed for it could result in serious
injury or death.
• Always select the correct accessories of the correct
size and design for the job that you are attempting to
perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is
in secure position, and will not move during repair.
1 YEAR LIMITED WARRANTY
• Astro Pneumatic Tool Co. warrants our products to the original
user against defective material or workmanship for a period of
1 year (except where noted on our price schedule) from the
date of 1st use. Astro reserves the right to determine whether
the product failed because of defective material, workmanship
or other causes and to charge back for missing parts.
Astro Pneumatic Tool Co., at its discretion, will repair products
covered under this warranty free of charge. The distributor
should direct the original user to return the product (with the
exceptions listed below) with the distributor’s name, address,
adequate proof of date of purchase or a copy of warranty card,
and a short note explaining the problem.
Failures caused by accident, alteration, or misuse are not
covered by this warranty.
• Astro Pneumatic Tool Co. or its authorized service
representatives must perform all warranty repairs. Any repair
to the product by unauthorized service representatives voids
this warranty. The rights under this warranty are limited to the
original user and may not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or
implied, including warranties of merchantability and fitness for
a particular purpose. Some states do not allow the exclusion
of limitations of incidental or consequential damages so the
above limitations may not apply to you.
Before use, check the parts diagram and part
number listing on page 4 to make sure all parts
are included. If any parts are missing or damaged,
please call your distributor.
SPECIFICATIONS:
Square Drive: 1/2"
Handle Type: Straight right angle
Clutch type: Oversized Hammer
Motor Housing: Aluminum w/ bed
liner finish
Air Exhaust: 360° Swivel Air Muffler
Air Inlet Thread: 1/4" NPT
Switch: 3-speeds in both F and R
Max Torque: 415 ft/lbs
Working Torque: 300 ft/lbs
Weight: 2.78 lbs
Length(from end to end): 3.46"
Height(from end to end): 10.4"
Free Speed: 9000 r.p.m.
Noise Level(sound pressure): 85 dB
Average Air Consumption: 4.2 CFM
Min. Hose Size: 3/8"
