![background image](http://html1.mh-extra.com/html/milwaukee/m12-hpt/m12-hpt_original-instructions-manual_1799315022.webp)
19
GB
English
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
WORKING TIPS
Use only system-compatible press fittings and press jaws designed
for them.
Consult the documents provided by the system supplier for hand-
ling and assembly instructions for fittings and pipes.
Check whether the nominal width of the press fitting corresponds
to the nominal width of the press jaws.
Make sure that the press jaw is fully closed when pressing is
complete.
Imperfect pipe joints must be compressed again using a new
fitting.
After finishing the work, check the installation with appropriate
testing equipment and assure that it is leakproof!
The press device is not suitable for continuous operation. Following
30 minutes of continuous operation, a short break of at least 15
minutes must be taken to allow the device to cool down.
SPECIFIED CONDITIONS OF USE
The devices and the press jaws are designed exclusively for the
press-fitting of pipes and fittings for which the relevant press jaws
are intended.
These press devices are intended exclusively for use with press jaws
approved by Milwaukee in agreement with the system supplier.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under “Technical Data” fulfills all the relevant regulations and the
directives 2011/65/EU (RoHs), 2004/108/ EC, 2006/42/EC and the
following harmonized standards have been used:
EN 60745-1:2009 + A11:2010
EN ISO 12100:2010
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
Winnenden, 2013-06-24
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
BATTERIES
New battery packs reach full loading capacity after 4 - 5 chargings
and dischargings. Battery packs which have not been used for some
time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery
pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition Every six
months of storage, charge the pack as normal.
MAINTENANCE
Check that the press jaw and drive rolls move freely.
Clean and grease the drive rolls, the bolt and press jaws when you
have finished work.
Service and repair work may only be carried out by authorised
specialist workshops.
The device contains hydraulic fluid. Hydraulic fluids pose a hazard
to groundwater. Uncontrolled draining or improper disposal is
punishable by law.
The next service deadline is indicated on the press device. This
service must be performed at least every 2 years or at the latest
when the LED display indicates that a service is due.
Replace worn press tools.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories. Should components need to be
replaced which have not been described, please contact one of
our Milwaukee service agents (see our list of guarantee/service
addresses).
If needed, service information of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on the
label and order the information at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364
Winnenden, Germany.
Summary of Contents for M12 HPT
