Milwaukee C18 PCG, Original Instructions Manual

Page: 10 / 39

18 19
C18 PCG
..................... 4315 81 04...
...000001-999999
.......................4500 N
...........................18 V
..........................2,3 kg
..........................2,5 kg
...........................68 dB (A)
...........................79 dB (A)
.......................< 2,5 m/s 2
..........................1,5 m/s
2
ENGLISH ENGLISH
TECHNICAL DATA CAULKING GUN
Production code.......................................................................
Feed force ...............................................................................
Battery voltage.........................................................................
Weight according EPTA-Procedure 01/2014 (1,5 Ah) .............
Weight according EPTA-Procedure 01/2014 (3,0 Ah) .............
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ........................
Sound power level (Uncertainty K=3dB(A)) .............................
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
h
.....................................................
Uncertainty K= .........................................................................
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under “Technical
Data” fulfi lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 62841-1:2015
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-11-10
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under “Technical Data” fulfi lls all
the relevant provisions of the following Regulations S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I.
2012/3032 (as amended) and that the following designated
standards have been used:
BS EN 62841-1:2015
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-11-10
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Read and understand the charger operator‘s manual
packaged with your charger.
Always wear goggles when using the machine.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. AEG Distributors off er to
retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System C18 chargers for charging System C18
battery packs. Do not use battery packs from other
systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
To reduce the risk of injury, electric shock, and damage to
the tool, never immerse your tool in liquid or allow a liquid
to fl ow inside the tool.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as
seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The caulking gun is intended to apply tube or sausage
pack caulks and adhesives to surfaces.In case of doubt,
please read the caulk or adhesive manufacturers‘
instructions.
Do not use this product in any other way as stated for
normal use.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it
from being overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the
machine automatically. To restart, switch the machine off
and then on again. If the machine does not start up again,
the battery pack may have discharged completely. In this
case it must be recharged in the battery charger.
ADVICE FOR OPERATION
Anti-Drip and Rod Release
The caulk gun features an automatic anti-drip to prevent
drips after the trigger is released. When the trigger is
released, the motor will run for a short time to release the
rod.
When a tube is emptied, the motor will run for a short time to
release the rod, then shut off . Release the trigger and
change the tube.
Overload
When an overload occurs, the tool will reach the maximum
drive force and continue to hold this maximum force until the
user releases the trigger. If material is not dispensing, make
sure that:
Nozzle tip is cut
Inner seal in the caulk tube is broken
Hardened material is removed from the nozzle
Caulk tube is not damaged or frozen
Rod is free of caulk/adhesive materials
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
MAINTENANCE
CAUTION! Carriage and rod must remain clean and free of
caulk and adhesive materials. Clean off materials
according to caulk/adhesive manufacturer’s
recommendations.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark