MIL'S ANTIGUA S127, Start-Up And Maintenance Instructions

Page: 40 / 48

ANTIGUA S27 / S52 / S127 / S162 / S252 / S327
520978-00 38
EN
Operating limit values
Operating range
Avoid the following conditions for the liquid ring pump:
•
Combination of several limit values
•
Starting frequency (
≤
10 1/h)
If more than one operating limit value is reached, consult the manufacturer for operating conditions.
Ambient conditions
• Temp
erature between -20°C and +40°C
•
Air humidity maximum 60%
•
Installation site dry
If temperatures are below +5°C, measures must be taken on the operator's side to prevent frost damage.
Conveyed product
General
•
Avoid the flow of several phases in waves or in plugs.
Operating pressures
•
Suction pressure:

e
operating fluid
(vapour pressure of the operating fluid) + 20 mbar
•
Compression overpressure:
≤
0,3 bar
•
Difference between suction and exhaust side: 200 mbar to 1 1 00 mbar
In case of non-condensed gas pure steam transport, supply the suction side according to the plant design
Inlet temperature
•
Saturated inlet temperature
≤
100°C
•
Dry inlet temperature
≤
200°C
Maximum size allowed of solid particles
Models S27 S52 S127 S162 S252 S327
Max. size of particle 0.1 mm 0.1 mm 0.1 mm 0.15 mm 0.15 mm 0.15 mm
Operating fluid
Physical properties
• Densit
y
≤
1 200 kg/m³
• Viscosit
y
≤
4 mm²/s
• pH : 6,5
to 8,5
•
Carbonate hardness 7°dH to 9°dH
Temperature
• POM
impeller: 10°C to 60°C (60°C on the exhaust pipe)
•
Stainless steel impeller: 10°C to 80°C (80°C on the exhaust pipe)
•
Avoid temperature variations
Operating pressures
•
The pressure loss must never be higher than 0.2 bar in any operating condition.
Maximum size allowed of solid particles
Models S27 S52 S127 S162 S252 S327
Max. size of particle 0.1 mm 0.1 mm 0.1 mm 0.15 mm 0.15 mm 0.15 mm
Volume flow rate at 33 mbar and 15°C
Models S27 S52 S127 S162 S252 S327
Volume flow rate 7.5 l/min 7.5 l/min 10 l/min 20 l/min 22 l/min 30 l/min
Minimum permissible volume flow rate
Models S27 S52 S127 S162 S252 S327
Min. volume flow
rate
1.5 l/min 1.5 l/min 2 l/min 4 l/min 4.4 l/min 6 l/min
Filling quantity up to the centre of the shaft
Models S27 S52 S127 S162 S252 S327
Filling quantity up to
the centre of the
shaft
0.5 l 0.6 l 1.1 l 2.9 l 3.9 l 5.9 l
Pipe charges
Models
Strengths Moments
F
x
F
y
F
z
M
x
M
y
M
z
S27 50 N 50 N 50 N 15 Nm 15 Nm 15 Nm
S52 50 N 50 N 50 N 15 Nm 15 Nm 15 Nm
S127 80 N 80 N 80 N 50 Nm 50 Nm 50 Nm
S162 100 N 100 N 160 N 30 Nm 30 Nm 100 Nm
S252 160 N 160 N 220 N 50 Nm 50 Nm 140 Nm
S327 200 N 200 N 250 N 100 Nm 100 Nm 180 Nm