Miller XT30C Manual Download Page 3

TABLE OF CONTENTS

SECTION 1 

  SAFETY PRECAUTIONS - READ BEFORE USING

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1. Symbol Usage

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Plasma Arc Cutting Hazards

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Additional Symbols For Installation, Operation, And Maintenance

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. California Proposition 65 Warnings

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5. Principal Safety Standards

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. EMF Information

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2 

  CONSIGNES DE SÉCURITÉ  

 LIRE AVANT UTILISATION

5

. . . . . . . . . . . . . . . . . . . . . . . . . .

2-1. Signification des symboles

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-2. Dangers liés au coupage à l’arc au plasma

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance

7

. . . . .

2-4. Proposition californienne 65 Avertissements

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-5. Principales normes de sécurité

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-6. Informations relatives aux CEM

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 

 SPECIFICATIONS

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-1. XT30 Specifications

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2. XT30 Torch Dimensions

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-3. XT30C Specifications

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4. XT30C Torch Dimensions

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-5. XT40 Torch Specifications

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-6. XT40 Torch Dimensions

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-7. XT60 Torch Specifications

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-8. XT60 Torch Dimensions

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 

 INSTALLATION

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-1. Installing 30 Ampere (XT30) Torch And Work Cable On Spectrum 375 X-TREME

(Stock No. 907 529), And Using Trigger Safety Lock

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2. Installing 30 Ampere (XT30) Torch And Work Cable On Spectrum 375 X-TREME

(Stock No. 907 303 And 907 339) Prior To Serial No. MB290336P, And Using

Trigger Safety Lock

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-3. Installing 30 Ampere (XT30C) Torch And Work Cable On Spectrum 375

(Stock No. 907532), And Using Trigger Safety Lock

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-4. Installing 30 Ampere (XT30C) Torch And Work Cable On Spectrum 375

(Stock No. 903 891), And Using Trigger Safety Lock

17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-5. Installing 40 Ampere (XT40) Torch And Work Cable On Spectrum 625 X-TREME

(Stock No. 907 404 And 907 531), And Using Trigger Safety Lock

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-6. Connecting And Disconnecting 40 Ampere (XT40) Torch On Spectrum 625 X-TREME

(Stock No. 907 579), And Using Trigger Safety Lock

19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-7. Connecting And Disconnecting Work Cable On Spectrum 625 X-TREME

(Stock No. 907 579)

19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-8. Connecting And Disconnecting 60 Ampere (XT60) Torch On Spectrum 875

And Spectrum 875 Auto-Line, And Using Trigger Safety Lock

20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5 

 OPERATION

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-1. Plasma Cutting System Practices

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. Sequence Of Cutting Operation

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-3. Sequence Of Piercing Operation

23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 6 

 MAINTENANCE & TROUBLESHOOTING

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-1. Routine Maintenance

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2. Shield Cup Shutdown System

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-3. Checking/Replacing Retaining Cup, Tip, And Electrode

25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4. Troubleshooting

26

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7 

 PARTS LIST

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WARRANTY

Summary of Contents for XT30C









































Reviews: