Mighty Mule MM560 Page 11 Installation Manual Download

Page: 11 / 44

MM560 Installation Instructions

Product identification and manual operation instruction
label installed on right hand side of control box.

1. KEEP CLEAR! Gate may move at any time.

2. Do not allow children to operate gate or play in gate area.

3. This gate is for vehicles only. Pedestrians must use separate entrance.

WARNING

MOVING GATE

Can Cause Injury or Death

1-800-543-GATE (4283) • www.mightymule.com

560

Logo and warning labels (2) installed on each side of
the operator housing

Control Box label with Manual Open and
Close instructions

Conforms to UL STD 325

Certified to CSA STD C22.2 No.247

Maximum Gate: 850 lb. (385.5 kg); 18 ft. (5.5 m)

Voltage: 12 Vdc; Frequency: 0 Hz; Power: 25 W

Class I Vehicular Swing Gate Operator.

MM500 SERIES DC Swing Gate Operator

P/N MM560

9901178

TO MANUALLY OPEN AND CLOSE THE GATE:

1. Turn control box power switch OFF.

2. Disconnect front or rear mount from mounting bracket.

3. Pull operator away from mounting brackets and move gate.

Disconnect operator ONLY when the control box power

switch is OFF and the gate is NOT moving.

Serial Number:

MM560-0000000

MMDDYY

GTO Access Systems, LLC - Tallahassee, Florida USA

TO MANUALLY OPEN AND CLOSE THE GATE

1. Turn opener power switch OFF.

2. Disconnect front and rear mount from mounting brackets.

3. Remove opener from mounting brackets and move gate.

Disconnect opener ONLY when the power switch is OFF and

the gate is not moving.

www.mightymule.com

1-800-543-GATE (4283)

Important Safety Information

These warning labels should be found at the locations specified below. If any of them are missing,

immediately contact GTO for replacements.

Required Safety Precautions for Gates

Summary of Contents for MM560













































Search results

Summary of Contents for MM560

Reviews:

Related manuals for MM560

Brands by name

Popular brands

Mighty Mule MM560, Installation Manual

Search results

Summary of Contents for MM560

Reviews:

Related manuals for MM560

Brands by name

Popular brands