background image

2

  

MM362 Installation Instructions

1. Determine Charging Options for Battery: Transformer OR Solar

NEVER USE TRANSFORMER AND SOLAR PANEL(S) AT THE SAME TIME!

It will damage the control board!

  

IMPORTANT

 

•  The Mighty Mule 362 is designed and intended for use with a 12 Volt automotive, lawn tractor or marine battery. 

The battery must be placed inside a weatherproof case and located within 6' of the control box. 

The 8' battery 

harness connects the battery to the control board

.

 

•  The battery charge is maintained by the 14 Volt transformer included 

OR 

optional solar panel(s). The transformer 

OR 

solar panel is connected to the control board using low voltage, 16 gauge, dual conductor, multi-stranded, 

direct burial wire [RB509] (page 26)

.

 

•  All low voltage wire used with the Mighty Mule Gate Opener must be 16 gauge dual conductor, multi-stranded, 

direct burial wire

.

 

•  The transformer is intended for indoor use. If the transformer can only be plugged into an outside electrical 

outlet, a weatherproof cover or housing 

must

 be used. 

 

•   If your gate is more than 1000' from an AC power source, you will need to use a solar panel charging kit 

(

minimum 10 watts

) . Refer to the Solar Panels and Gate Activity Chart below.

Solar Panel and Gate Activity Chart

The table and map illustrate the 

maximum number of gate cycles 

to expect per day in a particular 

area when using from 10 to 

20 watts of solar charging power prior to the 

battery depleting to a state where the unit will 

not function. The figures shown are for winter 

(minimum sunlight) and do not account for the 

use of any accessory items.

Accessories connected to your system 

will draw additional power from the 

battery and will require additional solar 

panels.

A deep cycle marine battery is recommended 

for solar and/or high traffic applications. 
NOTE: UP to 250 ft. of dual conductor, 16 

guage, multi-stranded wire may be used 

to allow installation of solar panels in direct 

sunlight.
See page 21:

10 Watt Solar Panel [FM123]

5 Watt Solar Panel [FM121]

Dual Gate 

Winter Ratings

Zone 1

Zone 2

Zone 3

10 Watts

8

16

26

15 Watts

11

20

30

20 Watts

14

28

38

Before You Begin

Summary of Contents for MM362










































Reviews: