background image

10

  

Mighty Mule 362-D Installation Instructions 

rev 12-14-15

Step 9 

Drill 

3

/

8

" holes through post as marked. Fasten post bracket assembly 

to the fence post using two 

3

/

8

" x 8" bolts, washers and lock nuts

You 

must use bolts that completely penetrate the post. 

Step 10

Drill 

3

/

8

" holes through the gate cross member as marked. Mount gate 

bracket using two 

3

/

8

" x 2 3/4" bolts, washers, and lock nuts

.

 

NOTE: 

After

 the gate opener installation is 

complete 

and operation 

of

 the opener system has been tested

, you should remove excess 

bolt length extending beyond the tightened nuts with a hacksaw or bolt 

cutters.

Round Tube & Chain Link Gate

Square Tube Gate

Mounting Plate 

Created for 

Decorative Gate

(required but not

supplied)

Remove excess bolt length 

with hacksaw or bolt cutters

FRONT VIEW

SIDE VIEW

FRONT VIEW

SIDE VIEW

Gate Bracket Mounting Examples

Round Metal Post

Round Wood Post

Square Metal Post

Square Wood Post

Remove excess bolt length 

with hacksaw or bolt cutters

SIDE VIEW

TOP VIEW

EXAMPLES

Gate Bracket 

Mounting 

Examples

Attach Opener Arm

Step 1

Attach the opener 

to the securely 

bolted post bracket 

assembly and gate 

bracket using clevis 

pins, bushings, 

and hairpin clips, or 

optional Pin Lock 

[FM133] (page 

26). Verify that the 

opener is level and 

adjust the post 

bracket assembly, if 

necessary.

Step 2

Install the SECOND gate opener and hardware on the second gate following the same procedures as the FIRST gate 

opener and hardware ("Installing Post Bracket Assembly and Gate Bracket" Steps 1–10). 
NOTE:  The power cable for the Second Opener should be run in PVC conduit under the driveway to protect it from 

damage due to lawnmowers, heavy equipment, etc. (See illustration on page 6.) NEVER SPLICE opener arm power 

cables. This will cause performance problems and may damage the opener.

Level Opener

Gate In Open Position 

LEVEL horizontal cross member

Post Bracket Assembly
bolted to fence post

Clevis Pin, Bushing, and Hairpin Clip

Clevis Pin, Washer, and Hairpin Clip

Gate Bracket bolted
to gate cross member

Fence Post

Summary of Contents for MM362-D





































Reviews: