background image

WARNING!

This equipment is similar to other gate or door equipment and meets or exceeds Underwriters 

Laboratory Standard 325 (UL 325). However, gate equipment has hazards associated with its 

use and therefore by installing this product the installer and user accept full responsibility for 

following and noting the installation and safety instructions. Failure to follow installation and safety 

instructions can result in hazards developing due to improper assembly. You agree to properly 

install this product and that if you fail to do so GTO Access Systems, LLC, shall in no event be 

liable for direct, indirect, incidental, special or consequential damages or loss of profits whether 

based in contract tort or any other legal theory during the course of the warranty or at any time 

thereafter. The installer and/or user agree to assume responsibility for all liability and use of this 

product releasing GTO Access Systems, LLC, from any and all liability.  If you are not in agreement 

with this disclaimer or do not feel capable of properly following all installation and safety 

instructions you may return this product for full replacement value.

READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY

 before attempting to install and 

use this automatic gate opener. This gate opener produces a high level of force.  Stay clear of the 

unit while it is operating and exercise caution at all times.

All automatic gate openers are intended for use on 

vehicular gates only

.

Printed in China for GTO Access Systems, LLC.

This product meets and exceeds the requirements of UL 325, the standard which 

regulates gate operator safety, by Underwriters Laboratories Inc.

GTO Sales

: 800-543-4283 • Fax 850-575-8912

GTO Technical Service

 800-453-1236

For 24 hour/day, 7 day/week Technical Service visit  http://support.gtoinc.com

For more information on Mighty Mule’s full line of Automatic Gate Openers and Access Controls visit www.mightymule.com

For more information on Mighty Mule’s full line of Automatic Gate Openers and Access Controls visit our website at www.mightymule.com

MM362-D

Installation Manual

Copyright

©

 2015 GTO Access Systems, LLC   rev 12.14.15

Summary of Contents for MM362-D





































Reviews: