Migatronic CWF Multi User Manual Download Page 12

12

Control panel

min

m

s

min

m

Units for parameters

Units of measurement of the selected parameter.

Wire feed motor

The relevant LED will illuminate when the wire feed 
motor is running forwards / backwards.

Control knob

All parameters are set by the use of the control 
knob.

Digital display

The digital display shows the value of the 
parameter being set. The unit of measurement 

of the parameter is shown on the right side of the digital 
display.

Selection of parameters

A parameter can be selected by means of the relative 
keypad. A bright indication light indicates the parameter 
selected.

Wire feed speed 

Setting of the wire feed speed.
Variable 0.20-5m/min.

Storage of parameters - programs 

This function enables storage of 20 different 
programs (often used wire settings) and shift from 

one complete program to another for changing values. 
By pressing the keypad the display shows a ”P” and a 
number: ”1”, ”2” etc. Each number includes a program 
with all parameters and functions of the CWF. To access 
the program the CWF must be disabled to “OFF”-mode. 
During normal use, programs for CWF are selected directly 
from the control panel in the PI. It is therefore possible to 
have several different CWF programs synchronised with 
different welding programs of PI.
At the beginning of welding, the PI will inform the 
specific CWF unit what will be the program to be used.
(CWF must be set to “ON-mode”)

s

min

m

1

2

2

3

3

4

4

5

Reset of welding programs 

The CWF needs to be disabled to “OFF”-mode. When the 
requested program has been selected, the 

 key pad 

should be kept pressed until the program number flashes 
on and off. The keypad can then be released again. All 
parameters of selected program have been set to factory 
settings.

Wire inching backwards 

The function is used for wire inching backwards. 
The selected inching speed is the same for all 

programs. Variable 0.2-5 m/min. 

Wire inching forwards

The function is used for wire inching forwards. The 
selected inching speed is the same for all programs. 

 Variable 0.2-5 m/min. 

Wire feed proces during TIG welding

The keypad should be pressed until the requested 
parameter is switched on in the table. 

Start delay

After arc ignition the start of the wire can be 
delayed to permit the creation of a suitable 

welding pool. Variable 0-10 sec.

Stop delay

At the beginning of slope-down, the welding 
machine signals to the CWF to stop the wire to 

prevent it from sticking to the workpiece. The time must 
be shorter than the slope-down period to prevent sticking 
to the workpiece. Variable 0-10 sec. 0 = disabled.

Retract time 

The time in which the wire is retracted after end 
of welding process. Variable 0-5 sec.

Retract speed

The speed of which the wire is retracted after end 
of welding process. Variable 0.2-5 m/min.

ON/OFF

This key is used to enable/disable the CWF unit. 
When the unit is disabled, the display shows “OFF” 

and the green LED will be turned off. Some operations, 
including access to user menu, can only be carried out 
when the unit is disabled. Flashing light will indicate:
  -  no CWF units have been configured on PI
  -  possible communications problem

Pulsed wire feeding

Is used for wire feeding in pulses. 
Pulsations can be synchronised with 

pulsation of current on the arc: in this case the LED is 
flashing. See below.
The values of speeds are fully independent, permitting 
the generation of “reversed” pulses: high speed at low 
currents and vice versa.

Main speed pulse time

The time for which the wire runs at main speed. 
If the welding machine has been set to slow pulse 

mode, the value of the parameter cannot be controlled 
and will be the same as the one on the welding machine. 
Variable 0.2-10 sec.

6

10

7

1

min

m

5

6

9

7

8

9

10

11

12

13

14

11

12

13

15

14

&

Summary of Contents for CWF Multi









































































Reviews: