Miele WT 2780 Operating Instructions Manual Download

Page: 49 / 92

The fluff which occurs during drying
can collect in the drum and also in the
suds container. Run the

Rinse out fluff

programme before the machine is used
again so that fluff cannot be deposited
on the next load (e.g. fluff from dark
garments being deposited on lighter
coloured items) or cause a blockage.

The

Rinse out fluff

programme must

not be used for rinsing laundry.
Make sure that there are no items of
laundry in the drum before starting
this programme.

Switch the machine on.

Turn the programme selector to the

Rinse out fluff

programme.

If there is a lot of fluff in the machine
select the

Water plus

extra option.

Press the

Start/Stop

button.

The fluff will be rinsed out after a few
minutes.

Remove any fluff remaining from
around the door seal and porthole
glass.

Switch the machine off.

The load sensor will have to be
recalibrated after running the

Rinse out

fluff

programme. See "Before using for

the first time".

Rinse out fluff programme

Summary of Contents for WT 2780





























































































Search results

Summary of Contents for WT 2780

Reviews:

Related manuals for WT 2780

Brands by name

Popular brands

Miele WT 2780, Operating Instructions Manual

Search results

Summary of Contents for WT 2780

Reviews:

Related manuals for WT 2780

Brands by name

Popular brands