Miele W 3652 WPS Operating Instructions Manual Download | Manualshive

Page: 41 / 68

background image

The drum door does not open when you press the Door button

Possible cause

Remedy

The machine is not
connected to the
electricity supply and / or
is not switched on.

Insert the plug in the socket and switch on and / or
switch the machine on with the

I-On/0-Off

button.

The safety lock has been
activated.

Deactivate the safety lock as described in "Safety
lock".

The electronic system lock
has been activated.

Deactivate the system lock as described in the
"Settings menu

J

".

Power cut.

Open the drum door as described in the next
section.

The door was not correctly
engaged.

Press hard against the lock side of the drum door
and then press the

Door

button.

There is still water in the
drum and the machine is
unable to drain.

Clean the drain filter and drain pump as described
in the next section.

For safety reasons the drum door cannot be opened if the suds temperature is
higher than 55°C.

Problem solving guide

41

«
...
39
40
41
42
43
...
»

Summary of Contents for W 3652 WPS





































































Reviews:

No comments

Related manuals for W 3652 WPS

Brand: GE Pages: 72

Brand: Haier Pages: 54

Brand: Haier Pages: 84

Brand: Haier Pages: 58

DW9-TFE1 Series

Brand: Haier Pages: 52

DW12-TFE3 series

Brand: Haier Pages: 28

Brand: Haier Pages: 18

Brand: lamber Pages: 70

Brand: Lamona Pages: 12

Brand: Majestic Appliances Pages: 19

Brand: NEFF Pages: 52

Brand: Foamit Pages: 6

Brand: Clatronic Pages: 42

Brand: Kärcher Pages: 24

Brand: ZANKER Pages: 40

Brand: F.F. Group Pages: 56

Brand: Prime Pages: 24

Brand: Hotpoint Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands