Miele W 2514 WPS Operating Instructions Manual Download Page 38 | Manualshive

Page: 38 / 68

background image

The drum door does not open when you press the Door button

Problem

Remedy

The machine is not
connected to the
electricity supply.

Insert the plug in the socket and switch on.

The machine is not
switched on.

Switch the machine on with the

I-On/0-Off

button.

Programme locking is
activated.

This is automatically deactivated at the end of a
programme. To deactivate it early see "Programme
locking and system lock".

The system lock is
activated.

To deactivate it see "Programme locking and
system lock".

Power cut

Open the drum door as described in “Opening the
door in the event of blocked drain outlet and/or
power failure”.

The door was not
correctly engaged.

Press hard against the lock side of the drum door
and then press the

Door

button.

There is still water in the
drum and the machine is
unable to drain.

Clean the fluff filter and the drain pump.

For safety reasons the drum door cannot be opened if the suds temperature is
higher than 55°C.

Cleaning and care

38

«
...
36
37
38
39
40
...
»

Summary of Contents for W 2514 WPS





































































Reviews:

No comments

Related manuals for W 2514 WPS

Brand: bar aid Pages: 16

Brand: Maytag Pages: 48

Brand: GE Pages: 60

Brand: Asko Pages: 36

Brand: Kärcher Pages: 37

Brand: SOGEDIS Pages: 23

Brand: arcelik Pages: 60

Brand: SPT Pages: 21

Performa LAW2400

Brand: Maytag Pages: 12

Brand: Insinger Pages: 104

Brand: Fieldmann Pages: 135

Brand: Hisense Pages: 34

Brand: CaterChef Pages: 44

Brand: Electrolux Pages: 40

Brand: Electrolux Pages: 2

Brand: Electrolux Pages: 48

Brand: Electrolux Pages: 56

Brand: Electrolux Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands