Miele TKB 440 WP Operating Instructions Manual Download Page 68

Page: 68 / 72

Programmable functions



Standby

To save energy the display and but‐

tons will go out after 10 minutes and

only the

Start/Stop

button will flash

slowly. You can alter this setting.

However, standby mode will not occur

in the event of a fault.
Options



Standby switched on:
The display and buttons will go

out after 10 minutes . .

. . . if no selection is made after

switching the dryer on.

. . . after a programme has star‐

ted.

However, the display and buttons

will remain lit up for 10 minutes

after a delay start time has

elapsed, after the end of the pro‐

gramme or at the end of the anti-

crease phase. The buzzer, if se‐

lected, will sound for 10 minutes

after the end of the programme.



Not in current programme (fac‐

tory default setting)

As described under



. Howev‐

er, the display and buttons will re‐

main lit up during the programme.



Off
The display and buttons will re‐

main lit up while the dryer is

switched on.

To switch the display and buttons back

on again

– Turn the programme selector or press

a button. Neither will have any effect

if a programme is running.

– Open the door while the dryer is

switched on.

Summary of Contents for TKB 440 WP









































































Search results

Summary of Contents for TKB 440 WP

Reviews:

Related manuals for TKB 440 WP

Brands by name

Popular brands

Miele TKB 440 WP, Operating Instructions Manual

Search results

Summary of Contents for TKB 440 WP

Reviews:

Related manuals for TKB 440 WP

Brands by name

Popular brands