Miele TKB 440 WP Operating Instructions Manual Download Page 31

Page: 31 / 72

Changing the programme sequence

You cannot change to another pro‐

gramme once a programme has started

(this prevents unintentional alterations).
If you move the programme selector,



will light up until you move the pro‐

gramme selector back to the original

programme.
You will need to cancel the current pro‐

gramme before you can select a new

one.

Cancelling a programme while

it is running and selecting a

new programme



Press the

Start/Stop

button.

The items will be cooled down, de‐

pending on the temperature reached

and how long they have been dried for.



will light up if you press the

Start/

Stop

button again during this cooling

down phase.



Press the



button to switch the dry‐

er off.



Press the



button to switch the dry‐

er on.



Select and start a new programme

straight away.

Adding or removing laundry af‐

ter a programme has started



Press the

Start/Stop

button.

The items will be cooled down, de‐

pending on the temperature reached

and how long they have been dried for.



will light up if you press the

Start/

Stop

button again during this cooling

down phase.



Danger of burning.

Do not touch the back of the drum

when adding or removing items. The

drum and the items can be very hot.



Add or remove items.



Close the door.

To continue with the programme:
(select a drying level first of all, if neces‐

sary)



Press the

Start/Stop

button.

Programme duration

Altering the programme sequence can

cause the programme duration shown

in the time display to be adjusted.

Summary of Contents for TKB 440 WP









































































Search results

Summary of Contents for TKB 440 WP

Reviews:

Related manuals for TKB 440 WP

Brands by name

Popular brands

Miele TKB 440 WP, Operating Instructions Manual

Search results

Summary of Contents for TKB 440 WP

Reviews:

Related manuals for TKB 440 WP

Brands by name

Popular brands